Kenmore Refrigerator 795.77713700 (79577713700, 795 77713700) Parts

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

Replacement drawer tray assembly that restores the bottom surface of a refrigerator drawer for organized storage and smooth operation. Use this part when a drawer bottom is cracked, warped, or not seating correctly to keep contents supported. What it does:

• Forms the bottom of a refrigerator drawer to support produce, packaged foods and other items.
• Replaces cracked, warped or otherwise damaged trays that can cause items to tip or spill.
• Helps drawers slide and seat properly by restoring the tray's fit and alignment.
• Restores a hygienic, easy-to-clean surface inside the drawer.

• Unplug the appliance or shut off power at the breaker before working on the refrigerator.
• Remove drawer contents and pull the drawer out; remove any retaining clips or fasteners holding the tray.
• Align the replacement tray with the drawer tracks/tabs and reattach any clips or screws; test drawer operation before returning contents.
• Use gloves to protect hands from sharp edges; for model-specific guidance.

This ice bucket stores ice produced by the refrigerator's ice maker, keeping ice contained and easy to access. It replaces a cracked, missing, or damaged bin to restore proper ice storage and hygiene. What it does:

• Holds and contains ice produced by the appliance's ice maker.
• Replaces cracked, warped, or broken buckets that allow ice to spill or become contaminated.
• Useful when the ice bucket is missing, jammed, or no longer seats correctly in the freezer.
• Helps ensure clean, manageable ice for dispensing or manual access.

• Remove remaining ice and unplug the refrigerator or switch the ice maker off before replacing the bucket.
• Align the bucket with the bin guides or tracks and slide it into place until it seats securely.
• Wash the new bucket in warm, soapy water and rinse before first use; avoid abrasive cleaners or high heat.

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

Right side upper hinge.

This bracket holder assembly is a structural mount used to secure an internal component, keeping it properly positioned during operation. Replacing a cracked or loose bracket restores support and helps prevent vibration, rattling, and misalignment.

• Provides a fixed mounting point to hold the supported part in place
• Maintains alignment to reduce vibration, rubbing, or noise
• Helps prevent shifting that can lead to premature wear
• Common symptoms: broken tabs or cracks, loose/misaligned component, rattling noises, visible damage to the old bracket

• Disconnect power; shut off water or gas if applicable
• Note screw locations and orientation; take a photo before removal
• Transfer any reusable clips or hardware from the old bracket
• Tighten fasteners evenly and avoid over-tightening to prevent damage

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This Magic Room cover is the replacement shelf panel that closes and protects the refrigerator's Magic Room compartment, keeping foods separated and organized for easy access. What it does:

• Replaces a cracked, chipped or missing Magic Room shelf panel
• Provides a flat surface over the Magic Room compartment to support containers and produce
• Helps keep items separated from the drawer below for better organization
• Restores proper fit and appearance inside the refrigerator

• Remove any items and the Magic Room drawer before installing the cover
• Align the panel with the shelf supports and lower into place until it snaps or seats securely
• Handle carefully to avoid chipping or scratching the plastic

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This grille cover protects the appliance's cooling/ventilation fan and helps direct airflow where it's needed. It restores the cabinet finish and keeps debris away from the fan housing for more reliable operation. What it does:

• Shields the fan from loose debris and small objects that can cause damage
• Helps channel airflow for proper cooling/ventilation
• Prevents direct contact with fan blades for improved safety
• Reduces rattling or vibration caused by damaged or missing grille

• Disconnect power to the appliance before beginning any work
• Remove any trim or access panels as required to reach the fan area
• Secure with the factory fasteners; do not overtighten to avoid cracking
• Handle edges carefully; wear gloves if needed and test operation after reassembly