Kenmore Refrigerator 795.78093900 (79578093900, 795 78093900) Parts

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This is a replacement retaining pin used to secure small moving parts and assemblies in compatible LG appliances. It restores proper alignment and holds components in place so assemblies operate smoothly. What it does:

• Secures and locates components within an assembly to prevent shifting or disengagement
• Helps maintain proper alignment for moving parts that can cause noise or malfunction when loose
• Commonly used where a small, durable metal pin is needed to retain clips, levers, or linkages
• Simple, single-purpose part — replacement when the original is bent, worn, or missing

• One retaining pin

• Unplug the appliance or disconnect power before servicing
• Access the affected assembly per the appliance service instructions; small fasteners or clips may need removal
• Use pliers or appropriate hand tools to remove/install the pin; avoid forcing to prevent damage
• Keep track of orientation and any associated clips or washers during disassembly

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

The Guide Assembly Rail is an OEM part for LG refrigerators. This assembly provides structural support and guidance for the refrigerator drawers, allowing them to slide in and out smoothly. It measures approximately 15 1/2 by 3 inches,.

Causes of a bad guide assembly rail can include wear and tear from regular use, damage from overloading the drawers, or physical impact. A compromised guide assembly rail can lead to difficulty in moving the drawers, affecting the usability of the refrigerator.

Symptoms of a bad guide assembly rail include:

• Drawers not sliding smoothly or getting stuck
• Drawers not aligning properly with the rail
• Unusual noises when opening or closing the drawers
• Visible damage or wear on the rail

This OEM LG part is also compatible with Sears/Kenmore models.

This door hinge assembly fits the "C" hinge position on select LG refrigerators. It supports the door and provides a smooth pivot so the door opens and closes properly, stays aligned, and seals to maintain efficient temperatures.

• Supports the refrigerator door at the designated "C" hinge location
• Provides the pivot point for smooth opening and closing
• Helps keep the door level and aligned for a proper gasket seal
• Replace if the door sags, rubs or binds, makes clicking/grinding noises, or the seal is inconsistent

• Disconnect power; shut off water supply if working near door wiring/lines
• Use two people to support and remove the door safely
• Remove hinge cover and fasteners; note hinge orientation before removal
• Install the new hinge, tighten fasteners securely, and verify door alignment and gasket contact

This is a replacement door gasket assembly that restores a tight seal around the refrigerator door to help keep cold air in and warm air out, improving cooling efficiency and reducing frost buildup. What it does:

• Seals the refrigerator door to prevent cold-air leaks and help maintain interior temperature.
• Helps reduce frost buildup and moisture on door shelves when the seal is intact.
• Can stop symptoms like warm spots near the door edge, noisy or overworking compressors, and visible gaps or tears in the existing seal.
• Restores proper door closure and can improve overall energy use when the original gasket is damaged.

• Disconnect power to the appliance before starting any service.
• Remove the old gasket carefully, then align the new gasket and press it into the door channel; work around the perimeter for an even fit.
• Check the gasket edge for full contact all the way around; run a paper test (paper should drag slightly when the door is closed) to verify seal.

This connector secures and transmits motion between the drawer drive and the sliding assembly, restoring smooth drawer movement and alignment. It's a direct-fit replacement that helps fix sticking, slipping, or non-moving drawers. What it does:

• Couples the drawer drive mechanism to the sliding gear, allowing the drawer to open and close reliably
• Replaces worn or broken connector teeth or mounts that cause skipping or jammed operation
• Helps correct uneven or noisy drawer movement caused by damaged linkage
• Restores proper engagement so the drawer responds to normal open/close controls

• One connector as shown

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Inspect surrounding gears, tracks, and mounting points; replace any damaged parts for best results
• Basic hand tools are typically required; handle plastic gears carefully to avoid further damage