Kenmore Refrigerator 795.78543807 (79578543807, 795 78543807) Parts

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

A replacement cover frame that restores the finished look and protection around the appliance control area. Replaces a cracked, warped, or scratched trim to keep controls secure and maintain appearance. What it does:

• Covers and protects the control panel edges from bumps, spills, and wear
• Keeps switches and buttons aligned and held in place
• Restores the appliance's finished appearance when the original frame is damaged
• Helps prevent debris from entering the control cavity

• Disconnect power to the appliance before beginning any work
• Remove any outer trim or control panel fasteners to access the existing frame
• Handle the part carefully to avoid scratching the finish during install

This part is a replacement compressor assembly. This part can be used to replace a broken, worn, or malfunctioning compressor in refrigerators. It works as a positive displacement pump that compresses the refrigerant. This assembly contains all parts required to successfully replace the compressor. Ensure that perishable foods are safely stored prior to the refrigerator being disconnected from the power source.This part is compatible with several different refrigerators manufactured by LG and various other brands. This is a genuine part made of high-quality, durable materials to ensure the best possible quality and fit.

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

This power control board assembly replaces a failed main control module to restore a unit's electronic control and power distribution. It helps the appliance respond correctly to user inputs and manage timed cycles. What it does:

• Manages power to key components and coordinates control signals across the appliance
• Replaces boards that cause no response, intermittent power loss, or unresponsive touch/knob controls
• Can correct erratic behavior tied to control logic or failed onboard components
• Works as the factory-style board designed for direct swap with the original unit

• Disconnect power before starting and follow OEM grounding precautions to avoid shock or board damage
• Handle the board by its edges; avoid touching soldered components or connector pins
• Verify connectors and wire harness locations match before securing; do not force connectors

Replacement guide assembly that secures and aligns internal TV components and cabinet panels to restore proper fit and reduce movement. Use this guide when a panel or internal module sits loose or causes vibration or rattling. What it does:

• Positions and supports internal components and circuit boards to maintain correct alignment
• Secures cabinet panels and trim to prevent gaps and movement
• Reduces vibration and rattling caused by loose internal parts
• Helps maintain proper routing for internal cables and connectors

• Disconnect power and remove the TV from its stand or wall before starting repair
• Use proper tools and keep screws/fasteners organized; handle panels and the display with care
• Follow the OEM service manual for disassembly/reassembly steps and torque specs

This is a factory-style screw used to secure components and panels on compatible LG appliances. It restores proper fit and reduces movement where a missing or stripped screw causes parts to sit loose. What it does:

• Fastens panels, brackets, or trim to appliance chassis to restore secure attachment
• Stops rattling or vibration caused by loose or missing fasteners
• Helps maintain proper alignment of removable parts for safe operation
• Serves as a direct replacement when the original screw is lost or damaged

• Screw

• Use the matching screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent damage to threads or plastic parts
• Replace only with the specified OEM screw to ensure fit and function
• Disconnect power to the appliance before accessing internal components when applicable

This is a replacement mounting screw used to secure appliance panels, trim or components. It restores proper attachment to reduce vibration and rattling and helps keep removable parts firmly in place during operation. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Restores secure fit when original screw is missing, loose, or stripped
• Reduces rattling and vibration caused by loose hardware
• Helps maintain proper alignment of removable covers and control panels

• Disconnect power and water before starting any repair
• Verify size and thread match the original screw before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten — overtightening can strip threads or crack plastic parts
• Keep small parts away from children and pets

This relay cover is a protective housing that shields a washer or dryer relay assembly from dust, moisture, and accidental contact, helping maintain safe and reliable operation of the appliance's control components. What it does:

• Protects the relay and nearby wiring from debris and moisture that can cause shorts or corrosion
• Helps prevent accidental contact with relay terminals during maintenance
• Reduces risk of electrical arcing or damage when relays switch under load
• Can improve long-term reliability of the control assembly when installed and intact

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove access panels as needed to reach the relay area; basic hand tools typically required
• Handle control board and components carefully to avoid damage from electrostatic discharge
• Replace only with the specified cover; do not modify or force-fit

This cover panel replaces a damaged or missing exterior trim piece to restore the appliance's appearance and protect internal components from dust and debris. It fits where the original cover was mounted and keeps wiring and parts shielded. What it does

• Covers and protects internal components from dirt and accidental contact
• Restores the appliance's exterior finish for a clean, finished look
• Helps reduce rattles by securing loose openings or edges
• Matches the original mounting locations for proper fit and alignment

• Disconnect power (unplug appliance or switch off breaker) before starting work.
• Removal/install typically requires basic tools (screwdriver or nut driver); keep original fasteners unless replacements are provided.
• Handle with care to avoid scratching the finish or breaking mounting tabs; avoid forcing clips.

This replacement hinge cover is a molded trim piece that snaps over the refrigerator door hinge to restore the appearance and protect the hinge area from dirt and damage. It keeps the hinge assembly concealed and the door looking finished. What it does:

• Covers and protects the door hinge assembly from dust, grease and accidental contact
• Restores a clean, finished look when original hinge cover is cracked, broken or missing
• Helps prevent debris buildup that can interfere with hinge movement
• Matches original mounting style for a secure snap-on fit when intact

• High-level replacement: typically snaps into place; inspect clips/tabs and align before pressing fully
• Power/disconnect: no electrical disconnect usually required, but follow appliance safety guidance and keep doors supported
• Handle gently to avoid breaking plastic clips during installation

This is a replacement mounting bracket that secures internal appliance components to the cabinet frame, restoring proper alignment and support for moving parts. It helps reduce vibration and prevents loose or sagging assemblies. What it does:

• Provides a stable mounting point for internal components to maintain correct positioning
• Helps stop rattling, knocking, or vibration caused by loose fittings
• Restores support for panels, assemblies, or mechanical linkages that rely on the bracket
• Useful when original bracket is bent, cracked, or otherwise damaged

• Follow manufacturer service manual for correct placement and fastener torque
• Use proper tools and retain all screws/fasteners; replace damaged fasteners as needed
• Disconnect power before accessing internal components to avoid shock or injury