Kenmore Refrigerator 795.78713801 (79578713801, 795 78713801) Parts

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

Right side upper hinge.

This connector joins two sections of the refrigerator's water tubing to create a secure, leak-resistant seal. Replace a cracked or loose connector to restore proper water flow to the dispenser and ice maker.

• Provides a sealed union between two water tubes in the appliance's water system
• Helps prevent air and water leaks that can impact dispenser and ice maker performance
• Typical failure signs include drips or puddles near the connection, visible seepage, or moisture alerts
• Also causes low/no dispenser flow or small or hollow ice cubes

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Prepare tubing with a clean, square cut; insert each tube fully into the connector until seated, then pull-test to retention
• Restore water and check all joints for leaks; purge air by dispensing water before normal use

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This rail connector secures a slide rail to its mounting point, keeping the rail aligned and stable so the assembly moves smoothly. Replace a cracked, worn, or missing connector to restore proper tracking and support.

• Joins the slide rail to its bracket or panel to maintain alignment and support
• Helps the rail travel smoothly without binding or coming off track
• Replaces broken, warped, or missing connectors that allow rails to loosen
• Typical signs of failure: rail separates, wobbles, sags, or won't stay engaged

• Disconnect power to the appliance; remove items to access the rail safely
• Remove the drawer/shelf and rail as needed to reach the connector
• Release locking tabs or fasteners, transfer the rail to the new connector, and seat it fully
• Reinstall components and test for smooth travel; wear gloves to protect hands from sharp edges

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This part is a replacement compressor assembly. This part can be used to replace a broken, worn, or malfunctioning compressor in refrigerators. It works as a positive displacement pump that compresses the refrigerant. This assembly contains all parts required to successfully replace the compressor. Ensure that perishable foods are safely stored prior to the refrigerator being disconnected from the power source.This part is compatible with several different refrigerators manufactured by LG and various other brands. This is a genuine part made of high-quality, durable materials to ensure the best possible quality and fit.

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement screw fastens appliance panels and components to maintain proper alignment and quiet operation. Use it to replace missing or worn screws that cause loose trim, rattling, or parts that won't stay secured. What it does:

• Secures panels, brackets, or trim to restore proper fit and reduce vibration noise
• Replaces missing or stripped screws that cause loose or wobbly components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small, discrete fastener commonly used in interior and exterior appliance assemblies

• Screw

• Disconnect power before accessing interior components to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for proper fit

This grille cover protects the appliance's cooling/ventilation fan and helps direct airflow where it's needed. It restores the cabinet finish and keeps debris away from the fan housing for more reliable operation. What it does:

• Shields the fan from loose debris and small objects that can cause damage
• Helps channel airflow for proper cooling/ventilation
• Prevents direct contact with fan blades for improved safety
• Reduces rattling or vibration caused by damaged or missing grille

• Disconnect power to the appliance before beginning any work
• Remove any trim or access panels as required to reach the fan area
• Secure with the factory fasteners; do not overtighten to avoid cracking
• Handle edges carefully; wear gloves if needed and test operation after reassembly

A replacement rail guide assembly that restores smooth, aligned drawer movement and support. Fits the refrigerator drawer slide system to reduce sticking, sagging, or uneven operation for safer access and proper cycling. What it does:

• Guides and supports a refrigerator drawer along its slide track for stable opening and closing
• Helps prevent the drawer from binding, tilting, or falling out of alignment
• Reduces scraping, grinding, or noisy operation caused by a worn guide
• Restores proper drawer travel and load support for daily use

• Disconnect power to the appliance before inspection or repair to avoid electrical hazards.
• Basic tools are usually required; remove the drawer to access the rail guide assembly.
• Verify left/right orientation before fastening; do not force parts into place.
• If screws or mounting clips are damaged, replace them to ensure secure installation.

This power control board assembly replaces a failed main control module to restore a unit's electronic control and power distribution. It helps the appliance respond correctly to user inputs and manage timed cycles. What it does:

• Manages power to key components and coordinates control signals across the appliance
• Replaces boards that cause no response, intermittent power loss, or unresponsive touch/knob controls
• Can correct erratic behavior tied to control logic or failed onboard components
• Works as the factory-style board designed for direct swap with the original unit

• Disconnect power before starting and follow OEM grounding precautions to avoid shock or board damage
• Handle the board by its edges; avoid touching soldered components or connector pins
• Verify connectors and wire harness locations match before securing; do not force connectors

This is a factory-style screw used to secure components and panels on compatible LG appliances. It restores proper fit and reduces movement where a missing or stripped screw causes parts to sit loose. What it does:

• Fastens panels, brackets, or trim to appliance chassis to restore secure attachment
• Stops rattling or vibration caused by loose or missing fasteners
• Helps maintain proper alignment of removable parts for safe operation
• Serves as a direct replacement when the original screw is lost or damaged

• Screw

• Use the matching screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent damage to threads or plastic parts
• Replace only with the specified OEM screw to ensure fit and function
• Disconnect power to the appliance before accessing internal components when applicable

This is a replacement mounting screw used to secure appliance panels, trim or components. It restores proper attachment to reduce vibration and rattling and helps keep removable parts firmly in place during operation. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Restores secure fit when original screw is missing, loose, or stripped
• Reduces rattling and vibration caused by loose hardware
• Helps maintain proper alignment of removable covers and control panels

• Disconnect power and water before starting any repair
• Verify size and thread match the original screw before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten — overtightening can strip threads or crack plastic parts
• Keep small parts away from children and pets