Kenmore Refrigerator 795.78739800 (79578739800, 795 78739800) Parts

The Water Line Connector is an OEM replacement part for LG refrigerators. It is responsible for connecting the water supply line from the home plumbing to the refrigerator's internal water distribution system, allowing for ice and water dispenser functionality. 

Causes of a bad water line connector can include cracking, leaks, or deterioration of the connector material over time due to regular water pressure and temperature fluctuations. Connectors may also become damaged if exposed to impact.

Symptoms of a bad water line connector include:

• Leaks at the connection point between the line and refrigerator
• Loose, slipping, or disconnected water line fitting  
• Reduced water pressure or no water flow to the dispenser
• Error codes related to water flow from the refrigerator diagnostics

 This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

The Drawer Guide is an OEM part for LG refrigerators. This part allows the smooth and effortless operation of the refrigerator's drawers, ensuring they glide in and out with ease. 

Causes of a bad drawer guide can be attributed to wear and tear over time, misalignment during installation, or damage from excessive force or improper use of the drawers.

Symptoms of a bad drawer guide include:

• Difficulty opening or closing the drawers
• Drawers getting stuck or not sliding properly
• Excessive friction or resistance when operating the drawers
• Drawers becoming misaligned or tilted
• Unusual noises or grinding sounds when using the drawers

This OEM LG part is also compatible with some Kenmore models.

The Compressor Overload Protector is an OEM replacement part for LG refrigerators. It plays an important safety role in protecting the compressor from damage due to excessive heat. Located near the compressor unit, the overload protector functions to shut off power to the compressor if temperatures become too high during operation.

Causes can include normal wear over time rendering it less responsive to temperature changes. Mineral or refrigerant deposits may also impede its ability to detect overheating conditions accurately.

Symptoms of a faulty overload protector include:

• Refrigerator fails to properly cool or the compressor does not run
• Circuit board or electrical component failure or burnout
• Lack of cold air production and higher than normal freezer/fridge temperatures

This OEM LG part is also compatible with some Sears/Kenmore models.

The Freezer Drawer Gear is an OEM part for LG refrigerators. It facilitates the smooth operation of the freezer drawer, allowing it to slide in and out effortlessly.

You should replace this gear if it becomes worn or damaged. Causes of a bad freezer drawer gear can include regular wear and tear, damage from overloading the drawer, or mechanical issues due to improper alignment or installation.

Symptoms of a bad freezer drawer gear include:

• Difficulty in opening or closing the freezer drawer
• The drawer not staying aligned or level
• Unusual noises when operating the drawer

This OEM LG part is also compatible with Sears/Kenmore.

This small torsion spring restores tension to the dispenser ice door lever so the chute door snaps closed after dispensing. It helps keep warm air and moisture out, reducing frost, condensation, and stray ice from the dispenser.

• Provides return tension for the dispenser ice chute door/lever
• Helps the chute door seal properly to limit warm air infiltration
• Worn or broken springs may cause the ice door to stay open or close slowly
• Symptoms can include frost/ice buildup in the chute, moisture at the dispenser, or cubes dropping/clumping

• Unplug the refrigerator or switch off the circuit breaker before servicing
• Remove the dispenser trim/panel to access the ice door mechanism; note spring orientation with a photo
• Use needle-nose pliers and eye protection—small springs are under tension and can snap
• After installation, cycle the dispenser to confirm the door opens/closes freely and seals

This fan motor assembly circulates air across the evaporator coils to keep temperatures even inside the refrigerator. Replacing a worn or noisy motor restores proper airflow for consistent cooling performance.

• Drives the evaporator fan to move chilled air through the cabinet and vents
• Helps maintain stable temperatures and reduces frost from stagnant air
• Common symptoms: weak or no airflow, loud or intermittent fan noise, temperature fluctuations, refrigerator section warmer than expected
• Failures may result from worn bearings, moisture exposure, or an open motor winding

• Disconnect power before servicing; wear cut-resistant gloves and eye protection
• Access the fan behind the interior rear panel; remove shelves/drawers as needed and avoid bending evaporator fins
• Note wire connector orientation and mounting order; transfer any reusable hardware from the original assembly as needed
• After reassembly, verify the fan spins freely and confirm operation before reloading the compartment

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The Cap Cover is an OEM part for LG refrigerators. This cover is designed to protect and secure various components within the refrigerator, such as the water filter or other internal mechanisms. Its role is to ensure that these components are shielded from debris, moisture, and potential damage, maintaining the overall efficiency and cleanliness of the appliance.

Causes of a bad cap cover can include wear and tear over time, cracks or breaks from accidental impacts, or warping due to exposure to temperature fluctuations. Misalignment or improper installation can also contribute to the cap cover becoming damaged or ineffective.

Symptoms of a bad cap cover include:

• Loose or missing cover
• Visible cracks or damage on the cover
• Debris or moisture accumulating in areas meant to be protected
• Misalignment or difficulty in securing the cover properly

This OEM LG part is also compatible with Sears/Kenmore.

Left Hand side

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

This small sleeve fits over the hinge pin to provide a smooth pivot and maintain proper door alignment. Replacing a worn bushing helps eliminate wobble and squeaks so the door opens and closes correctly.

• Supports the hinge pin/shaft to reduce friction and wear
• Helps keep the door aligned and at the correct height at the hinge
• Can resolve door wobble, sagging, squeaking, binding, or rubbing
• Improves smooth opening/closing and reduces play at the hinge

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door before removing hinge fasteners; note the order of spacers/washers
• Replace the bushing on the hinge pin and reassemble in the same stack-up
• Verify door alignment and operation after installation

This joint assembly is the connector that joins two refrigerator water tubes to form a tight, leak-resistant seal. Replace it to stop leaks at a line coupling and restore reliable dispenser and icemaker water flow.

• Connects two plastic water lines within the refrigerator's water system
• Maintains a watertight seal to prevent drips and air intrusion
• Common fix for leaks at a coupling or tubing that won't stay seated
• Symptoms include slow/sputtering dispenser, small/no ice production, or visible seepage at the connector

• Unplug the refrigerator and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Depress the connector collar to release the tubing; cut damaged tube ends square and fully insert tubing until it bottoms out
• Restore water and power, then check all connections for leaks

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power