Kenmore Refrigerator 795.78769800 (79578769800, 795 78769800) Parts

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

Replacement LED assembly restores screen illumination by replacing the TV's failed LED strips. Use this part to address dim, flickering, or uneven backlighting and improve overall picture visibility. What it does:

• Replaces the TV's backlight LED strips to restore even panel illumination.
• Commonly used when the screen is dim, has dark bands or spots, or the backlight flickers or fails while a faint image remains.
• Fits into the original LED channels and connects to the existing LED driver/board (direct-fit replacement when matched to correct model).
• Does not address unrelated failures such as main board, power supply, or panel matrix faults.

• Disconnect power and allow the TV to sit unpowered before starting—work only when fully de-energized.
• Handle the LCD panel and assembly carefully to avoid pressure damage; wear ESD protection when available.
• Verify LED operation before full reassembly (power up with the panel/coverings off only if you are comfortable and it's safe to do so).

This replacement temperature sensor measures the compartment temperature and reports it to the control board, helping your refrigerator maintain consistent cooling. Replace a failing sensor to restore accurate temperature readings and dependable performance.

• Monitors refrigerator/freezer temperature and relays data to the control
• Helps the system regulate compressor and fan operation for steady cooling
• A failing sensor can cause temperatures that are too warm or too cold
• May lead to extended run times, short cycling, or erratic cooling

• Disconnect power before servicing; wear cut-resistant gloves.
• Location varies by model; commonly clipped to the evaporator or mounted in an air duct/liner.
• Match the connector, route wiring along the factory path, and secure the probe in its original position.
• Restore power and allow up to 24 hours for temperatures to stabilize.

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This hinge bolt secures the hinge to the appliance cabinet or door, keeping alignment true and motion smooth. Replacing a stripped, missing, or corroded bolt helps restore proper door operation and reliable closing.

• Fastens the hinge to support and stabilize the door
• Helps maintain alignment for smooth opening and closing
• Replaces damaged, stripped, or missing hardware

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door to prevent strain on remaining hardware; enlist a second person if needed
• Note the order/orientation of any shims or washers and transfer them during reassembly
• Start threads by hand to avoid cross-threading; tighten securely without overtightening

Replacement ice bucket that collects and stores ice produced by the refrigerator ice maker, keeping ice contained and ready for dispensing. Molded plastic construction provides a clean catch area and helps reduce spills and freezer mess. What it does:

• Holds and stores ice produced by the ice maker so cubes are contained and accessible.
• Guides ice toward the dispenser/auger area to help ensure smooth delivery when seated correctly.
• Replaces cracked, broken or missing buckets that can cause leaks, spills or misalignment.
• Helps reduce loose ice and freezer clutter that can lead to ice jams or dispenser issues.

• Disconnect power to the refrigerator before removing or installing the ice bucket.
• Empty remaining ice and allow any frost to melt before installation to avoid blockages.
• Ensure the bucket is fully seated and aligned with the ice maker/dispenser so ice flows correctly.

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.

This PTC cover protects the refrigerator's PTC/compressor start device from dirt, moisture and accidental contact, helping the start device operate reliably. It's a simple replacement that restores the protective enclosure for the start assembly. What it does:

• Shields the PTC/compressor start relay and wiring from debris and moisture that can cause malfunctions
• Helps prevent accidental shorting or contact with terminals during operation or service
• Can resolve symptoms where the start device is exposed or the compressor area shows visible wear or damage
• Maintains correct positioning and protection of the start components for consistent compressor starting

• One PTC cover (protective enclosure) as shown

• Disconnect power to the appliance before starting any repair
• Replace only when the start device or cover is exposed and you can access compressor/start assembly safely
• Avoid bending or stressing terminals and wiring when removing or installing the cover

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

Motor Bracket secures the motor assembly, keeping it aligned and reducing vibration for reliable operation. Replacing a damaged bracket restores stable motor mounting and helps reduce noise and premature motor wear. What it does:

• Secures and supports the motor to maintain correct alignment and stable operation.
• Reduces motor vibration and operational noise when properly installed.
• A cracked, bent, or broken bracket can cause increased noise, vibration, or motor misalignment.
• Use when the existing bracket is bent, damaged, or failing to hold the motor securely.

• Disconnect power to the appliance before starting any repair.
• Access may require removing the cabinet or an access panel; keep track of fasteners.
• Installation typically requires basic hand tools; avoid forcing parts into position.

This genuine replacement basket door assembly restores a dishwasher's silverware basket closure so utensils stay secure during wash cycles. It replaces a broken, cracked, or missing basket door to keep small items contained. What it does:

• Replaces the small hinged door on the silverware basket that opens and closes for loading.
• Keeps forks, knives and spoons from falling out or shifting during a cycle.
• Prevents small items from interfering with spray arms and wash performance.
• Helps the basket maintain its intended fit and alignment in the lower rack.

• One basket door assembly as shown.

• Disconnect power to the appliance before starting any repair.
• Remove the lower rack to access the silverware basket and replace the door; no special tools usually required.
• Inspect hinge clips or pins for wear and replace if damaged to ensure proper operation.

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This vegetable tray assembly replaces a cracked or damaged crisper drawer and restores a secure, level shelf for storing produce. It provides the proper support and organization for fruits and vegetables in the refrigerator. What it does:

• Supports and contains fresh produce to prevent items from falling through or spilling
• Restores a smooth sliding drawer action when the original tray is broken or warped
• Helps keep produce organized and accessible on the refrigerator shelf
• Replaces worn or missing tray that can cause improper seating or uneven drawers

• Remove food and any loose items from the drawer area before beginning.
• Slide out the old tray and lift to remove; align and seat the new tray until it engages.
• No special tools typically required; refer to your refrigerator manual for model-specific instructions.
• Disconnect power and handle glass or trim components with care if removal of surrounding parts is necessary.

This cover assembly protects and diffuses the interior lamp so the appliance is evenly lit while keeping the bulb shielded from food and debris. It restores proper lighting visibility inside the compartment. What it does:

• Protects the interior lamp from spills, impacts, and contaminants
• Diffuses light for more even illumination of the compartment
• Helps prevent direct contact with the bulb for safer operation
• Commonly replaces cracked, discolored, or missing lamp covers that reduce light output

• Disconnect power to the appliance before servicing to avoid shock
• Remove and replace the cover gently; avoid excessive force that can crack the lens
• Handle and dispose of any broken plastic safely; inspect the lamp/bulb for damage
• After installation, restore power and verify the lamp operates and the cover sits securely

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit