Kenmore Refrigerator 795.78789800 (79578789800, 795 78789800) Parts

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

This is the condenser fan motor assembly located near the compressor at the back or bottom of the refrigerator. It draws air across the condenser coils to dissipate heat and keep the refrigeration system running efficiently. Replace this motor if the refrigerator is running warm, the compressor is overheating, or you no longer hear the fan running when the compressor is on.

Right side upper hinge.

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Sleeve that fits over the hinge pin for smooth door pivoting. Replace when doors wobble, squeak, or don't align properly. Confirm fit with your model.

Replacement LED assembly restores screen illumination by replacing the TV's failed LED strips. Use this part to address dim, flickering, or uneven backlighting and improve overall picture visibility. What it does:

• Replaces the TV's backlight LED strips to restore even panel illumination.
• Commonly used when the screen is dim, has dark bands or spots, or the backlight flickers or fails while a faint image remains.
• Fits into the original LED channels and connects to the existing LED driver/board (direct-fit replacement when matched to correct model).
• Does not address unrelated failures such as main board, power supply, or panel matrix faults.

• Disconnect power and allow the TV to sit unpowered before starting—work only when fully de-energized.
• Handle the LCD panel and assembly carefully to avoid pressure damage; wear ESD protection when available.
• Verify LED operation before full reassembly (power up with the panel/coverings off only if you are comfortable and it's safe to do so).

Refrigerator not cooling properly or showing temperature errors? This temperature sensor monitors compartment temps and sends readings to the control board.

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

This small plastic gear is part of the freezer drawer slide mechanism, allowing the drawer to open and close smoothly on its track. It meshes with the rail system to provide controlled, even movement of the drawer. Replace this gear if the freezer drawer is difficult to open, feels jerky or uneven when sliding, or if the original gear teeth are worn or broken.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.