Kenmore Refrigerator 795.79763905 (79579763905, 795 79763905) Parts

This is a genuine replacement mounting screw designed to secure appliance panels and internal components, restoring proper fit and stopping movement. Fits specified LG assemblies where the original screw is missing or damaged. What it does:

• Secures panels, brackets, or small components to prevent rattling and misalignment
• Restores proper attachment when original screw is stripped, lost, or broken
• Helps eliminate vibration noise caused by loose fasteners
• Matches OEM fit and thread form for reliable reassembly

• One mounting screw

• Disconnect power and water before beginning any service
• Use the correct driver and do not overtighten to avoid striping threads or cracking components
• Keep removed screws organized to ensure correct replacement locations
• If threads are damaged, replace mating clip or insert as recommended by OEM

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

Restore smooth, stable sliding with this rail guide assembly. It supports and aligns the sliding mechanism so your pull-out drawer, bin, or rack opens and closes evenly and seats properly.

• Guides the slide so the drawer/bin/rack moves in and out smoothly
• Helps keep the moving component level and aligned for proper closing
• Replacing a damaged guide can resolve sticking, binding, uneven travel, or scraping/grinding noises
• Can help when the drawer/rack won't extend fully or won't stay closed/seat correctly

• Disconnect power and remove the drawer/bin/rack and its contents for access
• Note orientation and transfer any mounting hardware from the original guide
• Install the new guide in the same position and tighten fasteners securely
• Manually slide to verify smooth travel before reloading

This rail guide assembly supports and guides a sliding refrigerator drawer/bin so it opens and closes smoothly. Replace a cracked or worn rail to restore proper alignment and prevent jamming or the drawer coming off its track. What it does:

• Attaches to the cabinet wall to support the sliding drawer/bin
• Provides a smooth track for extension and retraction
• Keeps the drawer level and aligned to prevent binding or rubbing
• Failure symptoms include a hard-to-open/close drawer, tilting on one side, popping off track, or visible cracks/broken tabs on the rail

• One rail guide assembly

• Disconnect power and remove the affected drawer/bin (and any glass shelf above) before starting
• Remove mounting screws, note their locations, and lift out the damaged rail
• Position the new rail, reinstall screws, and ensure the drawer engages the slide correctly
• Use caution around sharp edges; test drawer movement before reloading

Refrigerator shelf assembly that replaces a damaged or missing internal shelf, restoring flat, secure storage for food and containers. Helps keep items level and organized inside the fridge. What it does

• Replaces a broken, cracked, or missing refrigerator shelf to restore usable storage space.
• Provides a flat, stable surface for jars, bowls, and containers so items won't tip or slide.
• Prevents food from sagging between compartments and improves organization and accessibility.
• Matches factory-fit shelf mounts and seating points for correct alignment when installed.

• Remove all items from the shelf area before installing; handle glass or trim with care and wear protective gloves if needed.
• Slide or seat the shelf into the factory supports or track until it clicks or sits flat; some models require lifting slightly to engage rear tabs.
• No electrical disconnect is typically required, but follow the refrigerator owner's manual and disconnect power if instructed for your model.
• If the shelf has clips or trim pieces, verify they are properly engaged and undamaged before use.

This center hinge assembly supports the middle/center door on compatible refrigerators, restoring proper alignment and smooth opening. Replaces a worn or damaged hinge to help the door close evenly and reduce rubbing or sagging. What it does

• Provides the pivot point that keeps the center door aligned and balanced.
• Allows smooth door movement and helps maintain an even door gap.
• Corrects symptoms like door sagging, uneven gaps, rubbing, or doors that don't close fully.
• Works with factory mounting points for a direct replacement.

• Disconnect power to the appliance and empty or support the door before starting.
• Support the door securely while removing and installing the hinge to prevent injury or damage.
• Use common hand tools and follow the appliance service manual for door removal and reinstallation.
• Check door alignment and gasket seating after installation; adjust hinge position as needed per manufacturer instructions.

The Ice Door Solenoid Assembly is an OEM replacement part for LG refrigerators. This assembly controls the opening and closing of the ice door, which allows ice to be dispensed from the freezer to the exterior of the appliance. When you request ice, the solenoid activates, opening the ice door and permitting ice to pass through.

Symptoms of a bad Ice Door Solenoid Assembly include:

• Ice door not opening or closing properly
• Failure to dispense ice
• Ice accumulating or jamming at the dispenser

Causes for a malfunctioning Ice Door Solenoid Assembly can include electrical issues such as faulty wiring, wear and tear from frequent use, or mechanical problems affecting the solenoid's ability to move the ice door.

This OEM LG part is also compatible with Sears/Kenmore models.

Note: 90 degree elbow coupler (Fits 1/4" diameter tubing on each end) For 5/16" elbow connector, order part# 4932JA3009B.

The Water Line Union is an OEM part for LG refrigerators. This component connects sections of the water line, ensuring a secure and leak-free passage of water to the refrigerator's icemaker and water dispenser. It is an elbow tube union connector, which connects two tubes at a 90-degree angle.

Causes of a bad water line union can include wear and tear from frequent use, damage from high water pressure, or deterioration due to mineral buildup and age. A compromised union can lead to water leaks and disruption in the water supply.

Symptoms of a bad Water Line Union include:

• Water leaks around the connection points
• Reduced water flow to the icemaker or water dispenser
• Puddles or moisture near the refrigerator
• Unusual noises from the water line

This OEM LG part is also compatible with Sears/Kenmore.

Located in the left refrigerator door on french door models.

This connector cover is the small trim piece that shields and conceals the connection area on your refrigerator. Replacing a cracked or missing cover restores a clean, finished look and helps protect connectors from dust and accidental snags.

• Covers and protects the wiring and/or tubing connector cavity
• Helps keep debris out of the connection area
• Maintains proper routing and prevents snagging of harnesses
• Common signs it's needed: cracked or missing cover, exposed connectors, cover won't stay attached, cosmetic damage

• Disconnect power and turn off the water supply before beginning
• Remove any retaining screw(s) or release tabs to take off the old cover
• Position the new cover, ensuring wires/tubing aren't pinched; secure with original hardware
• Restore power/water and confirm the cover is fully seated