Kenmore Refrigerator 795.79772901 (79579772901, 795 79772901) Parts

Fix refrigerator not cooling properly or running constantly with a new drier assembly. Removes moisture from refrigerant. Requires EPA-certified technician.

Refrigerator not cooling evenly or freezer too warm? A failed DC motor stops air circulation. This motor ensures proper airflow for consistent temps.

Fixes refrigerator lights that won't turn on, stay on, or flicker when door opens. This door switch activates interior lighting. DIY install in 20 minutes.

Ice dispenser door won't close or stays open causing frost buildup? This small torsion spring restores tension to snap the chute door closed properly.

Secures components inside your refrigerator. Replace if broken or missing to prevent rattling and ensure proper part alignment. Confirm fit with model.

Creates an airtight seal to keep cold air in. Replace when worn, cracked, or leaking to restore stable temps and reduce frost. Confirm fit with model.

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Replace your cracked, broken, or missing refrigerator door basket. Restores secure storage for bottles, jars, and condiments on the inner door.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

Magnetic seal that runs around refrigerator door edge to keep cold air in. Replace if torn, loose, or failing to seal properly. Verify fit with model.

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

Replacement LED assembly restores screen illumination by replacing the TV's failed LED strips. Use this part to address dim, flickering, or uneven backlighting and improve overall picture visibility. What it does:

• Replaces the TV's backlight LED strips to restore even panel illumination.
• Commonly used when the screen is dim, has dark bands or spots, or the backlight flickers or fails while a faint image remains.
• Fits into the original LED channels and connects to the existing LED driver/board (direct-fit replacement when matched to correct model).
• Does not address unrelated failures such as main board, power supply, or panel matrix faults.

• Disconnect power and allow the TV to sit unpowered before starting—work only when fully de-energized.
• Handle the LCD panel and assembly carefully to avoid pressure damage; wear ESD protection when available.
• Verify LED operation before full reassembly (power up with the panel/coverings off only if you are comfortable and it's safe to do so).

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Secures the hinge to your refrigerator cabinet or door. Replace this bolt if stripped, missing, or corroded to restore proper door alignment and stability.

Door stop assembly for bottom-mount refrigerators. Mounts inside the door to control door closing and sealing. Replace if broken, cracked, or missing.

This ice gear transfers motor rotation to the refrigerator's ice mechanism so cubes can be dispensed or ejected. Replacing a worn or stripped gear restores smooth, reliable ice operation and helps eliminate grinding or clicking noises.

• Transfers drive from the motor to the ice mechanism (auger/ejector, depending on model)
• Helps move ice through the system for dispensing or harvest
• Common symptoms: no or slow ice dispensing, auger not turning, loud clicking/grinding from the ice bin
• Cracked or stripped teeth indicate the gear should be replaced

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the ice assembly per your model; note gear orientation for reassembly
• Align teeth carefully; do not force the gear onto the shaft
• Inspect related parts (drive coupler, auger, motor shaft) and replace any worn components to prevent repeat failure