Kenmore Refrigerator 795.79782902 (79579782902, 795 79782902) Parts

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Fix a refrigerator that won't start or hums but doesn't run with this compressor start capacitor. Restores reliable cooling when the compressor fails to start.

Secures the hinge to your refrigerator cabinet or door. Replace this bolt if stripped, missing, or corroded to restore proper door alignment and stability.

Door stop assembly for bottom-mount refrigerators. Mounts inside the door to control door closing and sealing. Replace if broken, cracked, or missing.

This ice gear transfers motor rotation to the refrigerator's ice mechanism so cubes can be dispensed or ejected. Replacing a worn or stripped gear restores smooth, reliable ice operation and helps eliminate grinding or clicking noises.

• Transfers drive from the motor to the ice mechanism (auger/ejector, depending on model)
• Helps move ice through the system for dispensing or harvest
• Common symptoms: no or slow ice dispensing, auger not turning, loud clicking/grinding from the ice bin
• Cracked or stripped teeth indicate the gear should be replaced

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the ice assembly per your model; note gear orientation for reassembly
• Align teeth carefully; do not force the gear onto the shaft
• Inspect related parts (drive coupler, auger, motor shaft) and replace any worn components to prevent repeat failure

Replacement ice bucket that collects and stores ice in your refrigerator's freezer. Molded plastic bin prevents spills and keeps ice organized.

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.

Replacement cover frame that restores the appearance around the appliance control area while protecting internal components. Use it to replace cracked, warped, or missing trim and keep the control panel edges aligned and secure. What it does:

• Replaces damaged or cracked trim around the control panel for a finished, uniform look
• Protects underlying switches and electronics from dust and light debris
• Helps keep control-panel edges aligned and prevents loose or flopping trim
• Improves overall appliance appearance after impact or wear

• Disconnect power to the appliance before starting any repairs
• Removal of the control panel or console is typically required; keep all fasteners for reassembly
• Handle edges carefully to avoid scratches or cuts and to prevent damage to the new frame

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Replaces broken or missing refrigerator door stop. Limits door travel to prevent over-extension and maintain proper alignment and smooth operation.

Replacement control panel cover frame for refrigerators. Restores the finished trim around controls. Replaces cracked, warped, or scratched frames.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Secures and pivots the ice bank door for smooth opening and proper sealing. Replace if door sags, won't close, or ice dispenser misaligns. Confirm fit.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks