Kenmore Washer Dryer Combo 970.-C90802-00 (970-C90802-00, 970 -C90802-00) Parts

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

For seal only use part number 131901400.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This push-in fastener secures plastic trim and interior panels to the appliance chassis, restoring a snug fit and reducing rattles or gaps. Simple, durable replacement for worn or missing retainers. What it does:

• Secures trim pieces, door panels, or interior components to the cabinet
• Keeps panels aligned to prevent vibrations and rattling noises
• Replaces missing or broken retainers that allow gaps or loose trim
• Works where a snap-in or push-retainer style fastener is specified

• Disconnect power to the appliance before servicing to avoid electrical risk.
• Remove surrounding trim or panels as needed to access the mounting hole.
• Push the fastener into the panel hole until it snaps or seats fully; ensure a flush fit.
• Replace with an identical fastener if size or stem design differs.

This replacement dryer drum with a galvanized back restores smooth tumbling and helps keep clothes moving and drying evenly. Designed to match the OEM shape and fit for compatible Frigidaire dryers. What it does:

• Replaces a worn, dented or rusted dryer drum so garments tumble properly
• Reduces fabric snags, rubbing marks and uneven drying caused by a damaged drum
• Helps eliminate metal-on-metal noise from a cracked or scored drum surface
• Works with the existing rollers, seals and belt—restores the drum's rotation

• Disconnect power and move the dryer to a clear work area before starting
• Support the drum as you remove the front and rear panels to avoid damage
• Basic hand tools are required; have a helper for heavier lifts
• Inspect rollers, glides and the drive belt during installation and replace if worn

Hex washer head. 5/16-18 x 0.625