Lg Refrigerator 68006 Parts

Adjustable leveling leg assembly stabilizes your refrigerator and ensures proper door alignment. Replace worn legs to reduce vibration and noise. Confirm fit.

This replacement fan blade mounts on the fan motor to move air for proper cooling. A cracked, loose, or damaged blade can cause noise and weak airflow—replacing it restores smooth, reliable air circulation. What it does:

• Drives airflow to help maintain stable temperatures throughout the appliance
• Supports efficient cooling by circulating air across key areas
• Common symptoms include rattling or scraping near the fan, vibration, or wobbling
• Replacement is recommended if the motor runs but the blade slips, doesn't spin, or is visibly damaged

• 1 fan blade

• Disconnect power before servicing
• Access the fan area by removing covers/shelves as needed
• Note blade orientation; pull the old blade straight off the shaft and press the new blade on until fully seated
• Spin the blade by hand to confirm clearances, reassemble, and restore power

Plastic cap that snaps over refrigerator door handle ends to cover mounting screws and finish the handle. Replaces lost, cracked, or broken caps.

Attaches to your refrigerator's crisper cover humidity vent to control airflow for produce storage. Replace if cracked, broken, or missing.

Center hinge assembly supports your refrigerator door at the middle pivot point for proper alignment and smooth operation. Replace if door sags or won't seal.

This is a defrost temperature sensor that monitors evaporator coil temperature and signals the defrost control board to initiate or end defrost cycles. It helps prevent excessive frost buildup on the evaporator, ensuring proper cooling performance. Replace this sensor if the refrigerator is not cooling properly, frost is accumulating heavily on the evaporator coils, or the unit is running continuous defrost cycles.

Support roller that mounts to the refrigerator base, allowing the unit to roll for cleaning or service. Replace if worn, broken, or causing uneven positioning.

Ice spilling into the freezer? This refrigerator ice bin collects and stores ice cubes from your icemaker. Simple snap-in installation takes minutes.

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

The refrigerator door stop guide is a small bracket or track component that controls how far your refrigerator door swings open and keeps it from opening too wide. It protects the door hinges, shelves, and walls from damage caused by the door swinging freely. Replace this part if your refrigerator door swings open too far, feels uncontrolled, or if the existing guide is cracked or broken.

Mounts on the shutter damper mechanism to adjust airflow settings. Replace a cracked, loose, or missing knob to restore smooth control and a finished look.

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Display not working or showing incorrect temperature? This refrigerator display control board manages temperature settings and interface functions.