Lg Refrigerator 78002 Parts

This is the DC motor that drives the condenser fan, typically located near the compressor at the bottom rear of the refrigerator. It circulates air across the condenser coils to dissipate heat and maintain efficient cooling. Replace this motor if the refrigerator is running warm, the compressor is overheating, or the fan is not spinning when the compressor is operating.

Center hinge assembly supports your refrigerator door at the middle pivot point for proper alignment and smooth operation. Replace if door sags or won't seal.

Attaches to your refrigerator's crisper cover humidity vent to control airflow for produce storage. Replace if cracked, broken, or missing.

This is a defrost temperature sensor that monitors evaporator coil temperature and signals the defrost control board to initiate or end defrost cycles. It helps prevent excessive frost buildup on the evaporator, ensuring proper cooling performance. Replace this sensor if the refrigerator is not cooling properly, frost is accumulating heavily on the evaporator coils, or the unit is running continuous defrost cycles.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

Display not working or showing incorrect temperature? This refrigerator display control board manages temperature settings and interface functions.

Mounts on the shutter damper mechanism to adjust airflow settings. Replace a cracked, loose, or missing knob to restore smooth control and a finished look.

The refrigerator door stop guide is a small bracket or track component that controls how far your refrigerator door swings open and keeps it from opening too wide. It protects the door hinges, shelves, and walls from damage caused by the door swinging freely. Replace this part if your refrigerator door swings open too far, feels uncontrolled, or if the existing guide is cracked or broken.

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Fridge not cooling or freezing? Compressor running constantly? This compressor set assembly restores cooling. Complex repair requiring professional tools.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Secure refrigerator components with this mounting screw. Replaces missing, stripped, or corroded fasteners. Restores tight fit and alignment.