Lg Refrigerator 78023 Parts

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Compressible foam gasket that seals refrigerator panels to prevent air and water leaks while reducing noise. Replace when worn to restore efficiency.

Secures and aligns the water pitcher in your refrigerator door. Replace if cracked, broken, or missing to keep your pitcher stable and organized.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This is a defrost sensor and control assembly that monitors the evaporator temperature in your refrigerator. It signals the defrost system to activate and terminate the defrost cycle at the proper times. Replace this sensor if your refrigerator is building up excessive frost on the evaporator coils, running constantly, or not maintaining proper temperatures.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This is a cover assembly that sits on top of the crisper drawers in the refrigerator, forming a shelf that helps regulate humidity and temperature in the crisper compartment below. It typically includes a glass or plastic panel with a frame. Replace this cover if it is cracked, broken, or no longer sits properly, which can lead to poor humidity control and premature spoiling of fruits and vegetables.

Left-hand drawer rail guide assembly for refrigerator bottom compartment. Replace when cracked, broken, or causing drawer misalignment or rough sliding.

Replace a cracked or missing produce bin so fruits and vegetables store at the proper humidity and your fridge stays organized. This direct-fit crisper drawer restores clean, reliable storage in the fresh-food section.

What it does

• Stores produce at a humidity level intended for fruits and vegetables
• Restores smooth pull-out/push-in operation when paired with intact slides
• Helps prevent spills and items dropping behind the drawers
• Replaces damaged bins that stick, wobble, or won’t seat correctly

What’s included
One vegetable/crisper drawer (sold individually).

Install notes

• Slide the old bin straight out; align and seat the new bin on the guides—no tools required
• Do not force; ensure the rail guides and center track are fully engaged
• Hand-wash only; avoid harsh cleaners that can stress and crack plastics

Usage tip
Keep heavier items on shelves above; overloading the bin can crack corners and stress the rails.

This is a rail guide assembly that allows a refrigerator drawer to slide in and out smoothly. It mounts inside the refrigerator cavity and supports the drawer's weight while enabling easy access to stored items. Replace this part if the drawer is difficult to open or close, feels wobbly, sticks, or has come off its track.

Drawer slide rail guide assembly for refrigerators. Installs to support and align drawers. Replace if cracked, bent, broken, or causing misalignment.

Replaces worn or damaged refrigerator drawer rail guide assembly. Restores smooth sliding when original guide is cracked, broken, or causing binding.