Lg Dryer 79661522211 Parts

Dryer won't start or stops mid-cycle? This door strike hook secures the door latch, engaging the switch so cycles can begin and run properly.

Fix a dryer door that won't stay closed or latched with this door lock assembly. Restores secure door closure for safe operation. Simple DIY repair.

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

This side vent hole cover seals unused ventilation openings in your dryer cabinet. It prevents lint buildup and maintains proper airflow through the designated exhaust path. Install this cover if you have an open hole causing lint to escape into areas where it shouldn't or affecting drying efficiency.

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Dryer not heating or taking too long to dry? This heating element restores proper heat generation. Moderate DIY repair solves no-heat issues fast.

This upper plate clip secures the control panel assembly to the top of the dryer cabinet, keeping it properly aligned and firmly in place. It is a small but important mounting component that prevents the control panel from shifting or becoming loose during operation. Replace if the clip is broken or missing and the control panel feels wobbly, does not sit flush, or has become detached.

Wire harness for dryers. Connects electrical components inside the cabinet. Replace if wires are frayed, damaged, or connectors are broken or melted.

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

This is the replacement body frame that secures and finishes the appliance front, restoring proper alignment and appearance. It provides a rigid mounting surface for the front panel and helps keep internal components protected from dust and debris. What it does

• Replaces a cracked, warped, or damaged front frame that causes gaps or poor fit
• Restores correct alignment of the front panel and door openings
• Covers and protects cabinet edges and mounting points from wear
• Helps prevent rattles and vibration by providing a stable mounting surface

• Frame/body replacement part

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove the front panel or door assembly per the service manual to access mounting screws
• Handle edges carefully; use proper tools and keep fasteners organized for reassembly