Lg Dryer 79671552610 Parts

This is a door lock and switch assembly that secures the washer door during operation and signals the control board that the door is properly closed. It prevents the door from being opened while the drum is spinning and allows the wash cycle to begin. Replace this assembly if the washer won't start, displays a door lock error code, the door won't lock or unlock, or the cycle stops unexpectedly.

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This is the gas tube assembly that connects the gas valve to the burner assembly inside the dryer. It channels gas from the manifold to the burner where it is ignited to produce heat for drying. Replace this tube if you detect a gas smell near the dryer, notice visible damage or corrosion on the tube, or if the dryer fails to heat properly.

This customized screw secures appliance panels and components for a reliable fit, helping maintain proper alignment and reduce vibration or rattling. Designed as a direct replacement to restore original fastening where the correct screw is required. What it does:

• Fastens panels, brackets, or components to prevent movement and vibration
• Restores secure mounting when a screw is missing, stripped, or damaged
• Helps stop rattling or intermittent contact caused by loose hardware
• Matches the OEM style for correct fit and function when replacing a lost or worn fastener

• Disconnect power to the appliance before performing any repairs
• Use the proper screwdriver or driver bit to avoid stripping the screw head
• Do not overtighten; snug until secure to avoid damaging threads or components
• Keep small parts away from children and pets during installation

This upper plate clip secures the control panel assembly to the top of the dryer cabinet, keeping it properly aligned and firmly in place. It is a small but important mounting component that prevents the control panel from shifting or becoming loose during operation. Replace if the clip is broken or missing and the control panel feels wobbly, does not sit flush, or has become detached.

This Pipe Assembly routes water into the appliance so the dispenser and ice maker can receive a steady supply. Replacing a damaged tube restores proper water flow and helps stop leaks or pooling inside or beneath the unit. What it does:

• Carries incoming water from the household supply to the appliance's internal water system
• Restores water delivery to the dispenser and ice maker when the original tube is cracked or blocked
• Prevents leaks and water damage caused by split, corroded, or pinched tubing
• Helps eliminate intermittent flow or weak dispenser output caused by a damaged water line

• One complete pipe assembly as shown

• Shut off the refrigerator's water supply and unplug the appliance before beginning
• Handle tubing fittings carefully; use proper tools to avoid damage or overtightening
• Inspect connection points and replace seals or clips if worn; test for leaks after reinstalling

Vertical connector bar for dryer drum assembly. Replace if cracked, bent, or broken. Structural part that connects vertical components inside cabinet.

This gasket creates an airtight seal between the dryer door and the drum opening to keep heated air inside the drum during operation. It is typically made of flexible felt or rubber and mounts around the door or the front of the tub. Replace this seal if you notice heat escaping around the door, longer drying times, or visible wear, tears, or hardening of the gasket material.

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

Secures the door hinge to your dryer cabinet for proper alignment and smooth operation. Replace if the door sags, rubs, or won't stay open. Confirm fit with your model number.

This is a damper mechanism attached to the dryer door hinge that controls how the door opens and closes. It provides resistance so the door doesn't swing open too quickly or slam shut. Replace this assembly if the dryer door swings open uncontrollably, won't stay closed, or the damper no longer provides smooth resistance when opening or closing.

This handle assembly replaces a worn, cracked or broken refrigerator door handle to restore a secure grip and smooth door operation. Designed to mount in the factory handle location for a clean, factory appearance. What it does

• Provides a finished grip surface for opening and closing the refrigerator door.
• Replaces damaged or loosened handles that can catch, wobble, or separate from the door.
• Helps prevent cabinet and door edge damage caused by attempting to open with a compromised handle.
• Matches the factory fit and mounting points for straightforward replacement when compatible.

• Disconnect power to the appliance and remove food/items from the door area before beginning work.
• Support the door while removing fasteners; some models use hidden screws or trim pieces—retain all hardware.
• Use common hand tools and avoid over-tightening fasteners to prevent handle or door damage.

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners