Lg Microwave 80043 Parts

Fix F4 error codes or sensor cook failures with this microwave humidity sensor. Restores automatic cooking cycles. Moderate DIY difficulty.

Metal mounting plate that secures the microwave chassis to the wall or cabinet. Replace if bracket is bent, cracked, or missing during installation.

This is a glass or plastic lens cover that sits over the interior light bulb inside the microwave. It protects the light bulb from grease, food splatter, and heat while allowing light to illuminate the cooking cavity. Replace this lens if it is cracked, cloudy, discolored, or missing, which can leave the bulb exposed to damage and reduce interior visibility.

This is a resin waveguide cover that sits inside the microwave cavity and shields the magnetron opening from food splatter and moisture. It allows microwave energy to pass through while protecting internal components. Replace this cover if it is cracked, burned, warped, or if you notice arcing or sparking during operation.

If your microwave shuts off mid-cycle or won't heat, the thermostat may have failed. This safety control monitors temperature and protects components.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This holder secures the door lock assembly to the washer, keeping the latch and lock mechanism aligned for reliable door closure and operation. Replaces a worn or broken lock mounting bracket to restore proper door engagement. What it does:

• Mounts and supports the washer door lock assembly to keep the latch aligned
• Holds the lock in place so the door can fully close and lock during cycles
• Common symptoms: door won't latch, door comes loose, washer won't start, or door/lock error codes
• Prevents excessive movement that can damage the lock or striker

• Unplug the appliance and turn off water supply before beginning work
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reassembly
• Handle edges and the door/lock assembly carefully to avoid damage

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Replaces a cracked, chipped, or broken glass turntable tray inside your microwave cavity. Typically damaged during cleaning or accidental impacts.

Fix a microwave that won't heat with a new magnetron. This part generates the microwave energy needed for cooking. Moderate DIY repair, 1-2 hours.

This is a small fan blade that sits inside the microwave cavity and rotates to distribute microwave energy evenly throughout the cooking area. It helps prevent hot and cold spots in your food by stirring the microwave waves as they enter the cavity. Replace this blade if your microwave heats unevenly, if the blade is cracked or warped, or if you hear unusual noises during operation.

Microwave won't heat? A failing high-voltage capacitor disrupts the heating circuit. This part stores electrical energy for consistent operation.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

Reduces cooking odors in your microwave. Replace every 6 months for optimal performance. Confirm fit with your model number before ordering.