Lg Range 80404 Parts

This is a glass or plastic lens cover that sits over the interior light bulb inside the microwave. It protects the light bulb from grease, food splatter, and heat while allowing light to illuminate the cooking cavity. Replace this lens if it is cracked, cloudy, discolored, or missing, which can leave the bulb exposed to damage and reduce interior visibility.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

Microwave not heating or sparking inside? This high voltage capacitor stores power for the magnetron. Common repair taking 30-45 minutes with care.

This thermostat controls oven/dryer temperature by opening or closing its contacts as the appliance reaches set temperatures, helping maintain safe and consistent operation. Replaces a worn or failed thermostat to restore proper temperature regulation. What it does:

• Senses temperature and interrupts heating when limits are reached to prevent overheating
• Re-establishes heating when temperature falls, maintaining normal cycle performance
• Commonly installed when an appliance won't heat, overheats, or cycles erratically
• Works as a direct replacement for the OEM thermostat designed for compatible LG units

• One thermostat

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Note wire locations or take a photo before removing wiring; reconnect wires to the same terminals
• Use a multimeter to verify thermostat continuity and correct operation before and after replacement

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This holder secures the door lock assembly to the washer, keeping the latch and lock mechanism aligned for reliable door closure and operation. Replaces a worn or broken lock mounting bracket to restore proper door engagement. What it does:

• Mounts and supports the washer door lock assembly to keep the latch aligned
• Holds the lock in place so the door can fully close and lock during cycles
• Common symptoms: door won't latch, door comes loose, washer won't start, or door/lock error codes
• Prevents excessive movement that can damage the lock or striker

• Unplug the appliance and turn off water supply before beginning work
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reassembly
• Handle edges and the door/lock assembly carefully to avoid damage

Replacement mounting screw for microwave panels and components. Secures brackets, vents, and assemblies. Needed when original fastener is missing or damaged.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Replacement mounting screw for microwave installation and assembly. Use when original screws are lost, stripped, or damaged during service or relocation.

This AC synchronous drive motor powers the rotation of the appliance's drum/assembly, restoring smooth, timed rotation and reliable operation. Designed as a direct replacement for the original synchronous motor. What it does

• Spins the drum/assembly at consistent speed for normal cycles and timed motion
• Replaces a worn or failed synchronous motor to stop intermittent or no-rotation symptoms
• Helps eliminate humming, slow spin, or start-fail issues caused by a faulty motor
• Works with the appliance's control system to maintain synchronized motor timing

• One AC synchronous drive motor (single unit)

• Disconnect power before beginning any repair to avoid electrical shock
• Handle wiring connectors and mounting hardware carefully; match connectors to original locations
• Typical install requires removing access panels and the drum/assembly—refer to your model's service manual

This is a small holder that mounts inside the microwave cavity to support a cooking rack or auxiliary shelf. It keeps the rack securely in position so food can be elevated for more even heating. Replace this support if it is broken, missing, or no longer holds the cooking rack firmly in place.

Replace your microwave grease filter to maintain proper ventilation and reduce odors. Filters grease and smoke from cooking. Verify fit with your model number.

Mounting bracket for microwaves. Secures the unit to cabinetry or wall. Replace if bent, cracked, or missing to ensure proper installation support.

Turntable not rotating in your microwave? This synchronous motor powers the turntable rotation. Moderately easy repair that restores even heating.