Lg Wall Oven 85473 Parts

Holds the light bulb and maintains electrical connection in your microwave. Replace when socket is cracked, heat-damaged, or causes flickering lights.

Fix a microwave that won't start or runs with the door open. This door interlock switch ensures safe operation by detecting when the door is fully closed.

Fix F4 error codes or sensor cook failures with this microwave humidity sensor. Restores automatic cooking cycles. Moderate DIY difficulty.

Microwave won't start or stops mid-cycle? This door latch assembly engages door hooks and activates interlock switches to restore proper operation.

This is a glass or plastic lens cover that sits over the interior light bulb inside the microwave. It protects the light bulb from grease, food splatter, and heat while allowing light to illuminate the cooking cavity. Replace this lens if it is cracked, cloudy, discolored, or missing, which can leave the bulb exposed to damage and reduce interior visibility.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

Microwave won't heat? A failing high-voltage capacitor disrupts the heating circuit. This part stores electrical energy for consistent operation.

If your microwave shuts off mid-cycle or won't heat, the thermostat may have failed. This safety control monitors temperature and protects components.

This is a resin waveguide cover that sits inside the microwave cavity and shields the magnetron opening from food splatter and moisture. It allows microwave energy to pass through while protecting internal components. Replace this cover if it is cracked, burned, warped, or if you notice arcing or sparking during operation.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

Factory mounting screw secures panels, brackets, and internal components in microwaves. Replace missing, stripped, or corroded screws to keep assemblies tight.

Mounting screw for microwave assembly. Secures internal or external components. Replace if stripped, missing, or damaged during repair or installation.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Reduces cooking odors in your microwave. Replace every 6 months for optimal performance. Confirm fit with your model number before ordering.