Lg Range 86009 Parts

Microwave not heating or sparking inside? This high voltage capacitor stores power for the magnetron. Common repair taking 30-45 minutes with care.

This thermostat controls refrigerator temperature by opening and closing the cooling circuit as needed to maintain set temperatures. Replaces a failed or intermittent temperature control to help restore consistent cooling and food safety. What it does:

• Senses cabinet temperature and signals the cooling system to cycle on or off
• Stops continuous running when thermostat fails closed or restores cooling when stuck open
• Commonly used to address inconsistent temperatures, warm spots, or compressor short-cycling
• Passive electromechanical component—no programming required

• Disconnect power to the appliance before starting any repair
• Handle terminals and sensor capillary carefully to avoid bending or damage
• Confirm wire connections match the old thermostat and secure spade terminals firmly

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This holder secures the door lock assembly to the washer, keeping the latch and lock mechanism aligned for reliable door closure and operation. Replaces a worn or broken lock mounting bracket to restore proper door engagement. What it does:

• Mounts and supports the washer door lock assembly to keep the latch aligned
• Holds the lock in place so the door can fully close and lock during cycles
• Common symptoms: door won't latch, door comes loose, washer won't start, or door/lock error codes
• Prevents excessive movement that can damage the lock or striker

• Unplug the appliance and turn off water supply before beginning work
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reassembly
• Handle edges and the door/lock assembly carefully to avoid damage

This is a lamp cover or light lens that fits over the interior light bulb in a microwave. It protects the bulb from moisture, grease, and food splatter while allowing light to illuminate the cooking cavity. Replace this cover if it is cracked, yellowed, melted, or missing, which can leave the bulb exposed to damage.

If your microwave door won't close or latch properly, this door latch assembly restores secure closing. Moderate DIY repair in about 30 minutes.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Fix a microwave that won't start, heat, or respond to buttons with a new control board assembly. This repair restores full function to your microwave.

This is an installation hardware kit that includes the bolts, screws, brackets, and fasteners needed to mount an over-the-range microwave to the wall and upper cabinet. It ensures the microwave is securely attached and properly supported during use. Use this kit if you are installing a new microwave or if original mounting hardware has been lost, stripped, or damaged.

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

Replace your microwave grease filter to maintain proper ventilation and reduce odors. Filters grease and smoke from cooking. Verify fit with your model number.

Replaces cracked, broken, or warped outer door frame on your microwave. Secures door glass and maintains proper alignment. Restores appearance.

Turntable not rotating in your microwave? This synchronous motor powers the turntable rotation. Moderately easy repair that restores even heating.