Lg Microwave DOTRC17B Parts

Thermistor is a temperature-sensing replacement that monitors refrigerator and freezer temperatures so the control board can regulate cooling. Replacing a faulty thermistor restores accurate temperature readings and helps stabilize cooling performance. What it does:

• Senses interior/evaporator temperature and sends a signal to the control board for temperature regulation.
• Helps prevent erratic cooling, long run-times, or inconsistent compartment temperatures when operating correctly.
• Faulty thermistors can contribute to excessive frost, failed defrost cycles, or compressor cycling issues.
• Use when the existing sensor fails to report correct temperatures or the part number matches.

• Always disconnect power to the appliance before servicing to avoid shock or damage.
• The sensor is typically mounted on or near the evaporator or inside a cabinet wall; access may require removing panels or covers.
• Handle the sensor and wiring harness gently; avoid pulling on wires or bending the sensor element.

This magnetron is the high-voltage tube that produces the microwave energy used to heat food in a countertop microwave. Replacing a failing magnetron restores normal heating performance and stops weak or no-heat conditions. What it does

• Generates microwave energy that heats food inside the oven cavity
• Stops microwave from heating when the tube fails or output is reduced
• May be the cause of loud humming, arcing, or burning smells during operation
• Works with the oven's high-voltage system and waveguide to deliver even cooking

• One magnetron

• Disconnect power before servicing and discharge the high-voltage capacitor; high-voltage components can be lethal
• Inspect and retain any mounting hardware, gaskets, and the waveguide cover for proper reassembly
• Do not operate the oven with the waveguide cover or protective shielding removed

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This holder secures the door lock assembly to the washer, keeping the latch and lock mechanism aligned for reliable door closure and operation. Replaces a worn or broken lock mounting bracket to restore proper door engagement. What it does:

• Mounts and supports the washer door lock assembly to keep the latch aligned
• Holds the lock in place so the door can fully close and lock during cycles
• Common symptoms: door won't latch, door comes loose, washer won't start, or door/lock error codes
• Prevents excessive movement that can damage the lock or striker

• Unplug the appliance and turn off water supply before beginning work
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reassembly
• Handle edges and the door/lock assembly carefully to avoid damage

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Replace your cracked or missing microwave interior metal tray shelf. Provides stable support for food and containers while containing spills.

Fix a microwave that overheats or shuts off unexpectedly with this cooling fan motor. Direct replacement part restores proper ventilation and cooling.

Microwave turntable not rotating? This synchronous AC motor drives the turntable rotation. Common DIY repair, typically takes 15-30 minutes.

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a