Lg Refrigerator LDC22370SW Parts

This replacement ice bucket stores the ice produced by your refrigerator's ice maker and positions it for dispensing. Replace a cracked, warped, or missing bin to restore clean, reliable ice storage and proper dispenser performance.

• Collects and holds harvested ice until dispensed
• Seats securely to support consistent ice dispensing
• Helps prevent spills and stray ice in the compartment
• Replace if cracked, warped, has broken tabs, won't sit flush, or the dispenser struggles/jams due to a damaged bin

• Disconnect power to the refrigerator and switch the ice maker off
• Remove any ice, then pull the old bucket straight out
• Clean the area, then slide the new bucket in until fully seated
• Restore power and resume ice production

Center hinge assembly supports the refrigerator door at mid-cabinet, providing smooth pivot and proper alignment. Replace if door sags or seals poorly.

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Compressible foam gasket that seals refrigerator panels to prevent air and water leaks while reducing noise. Replace when worn to restore efficiency.

Secures and aligns the water pitcher in your refrigerator door. Replace if cracked, broken, or missing to keep your pitcher stable and organized.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This is a defrost sensor and control assembly that monitors the evaporator temperature in your refrigerator. It signals the defrost system to activate and terminate the defrost cycle at the proper times. Replace this sensor if your refrigerator is building up excessive frost on the evaporator coils, running constantly, or not maintaining proper temperatures.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

Secure refrigerator panels, brackets, and internal components with this replacement mounting screw. Ideal for missing, stripped, or damaged fasteners.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

Refrigerator lamp light cover assembly protects the interior bulb and sensor. Replace if cracked, discolored, or broken to restore proper lighting.