Lg Range LDG5315ST Parts

Replace a cracked, discolored, or missing burner cap that's causing uneven flames or allowing spills into the burner assembly. Fits over the burner head.

Secures the gas burner nozzle in your range cooktop. Replace this holder if it's cracked, broken, or no longer holding the nozzle firmly in position.

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

Replace your range control panel if buttons aren't responding or the display is blank. This electronic user interface restores touchpad function and cycle selection.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Fix burners or oven not lighting with this gas valve assembly. Controls gas flow to restore safe ignition and consistent heating in your range.

Fixes intermittent power or control issues caused by damaged wiring. This harness restores electrical connections between range components for reliable operation.

Lower cabinet support base that stabilizes your range and protects internal components. Replace if cracked, broken, or causing wobble for secure mounting.

This heater cover is the replacement housing that protects the dryer heater assembly and helps direct airflow for reliable drying performance. It restores proper heater positioning and helps prevent contact with heating components. What it does:

• Protects the heater assembly and surrounding components from debris and direct contact
• Helps channel airflow through the heater area for consistent drying
• Can reduce rattling or noise caused by a damaged or loose heater cover
• May be replaced when cover is cracked, warped, or missing fasteners

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury
• Inspect mounting tabs and fasteners; replace any damaged clips or screws for secure fit
• Minor disassembly of the dryer cabinet may be required; keep track of removed screws and panels
• If you smell burning or see damaged wiring, stop.

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

If your gas range burner won't ignite or heat unevenly, this surface burner assembly restores reliable flame and even cooking. Moderate DIY repair.

Fix intermittent power loss or electrical failures in your range with this wiring harness. Restores proper connections between components. Moderate DIY.

Range controls not responding or features intermittent? This wiring harness restores power and signal connections between components for reliable operation.

Fix misaligned or wobbling burner flames with this nozzle holder. Secures the nozzle in place to restore proper gas flow and even heating on your range.