Lg Refrigerator LDN22470ST Parts

Refrigerator won't power on or loses power intermittently? This power cord assembly replaces frayed or damaged cords to restore safe, reliable operation.

Conceals and protects the door hinge area on your refrigerator. Replace this cover if cracked, loose, or missing to restore a clean appearance.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This replacement ice bucket stores the ice produced by your refrigerator's ice maker and positions it for dispensing. Replace a cracked, warped, or missing bin to restore clean, reliable ice storage and proper dispenser performance.

• Collects and holds harvested ice until dispensed
• Seats securely to support consistent ice dispensing
• Helps prevent spills and stray ice in the compartment
• Replace if cracked, warped, has broken tabs, won't sit flush, or the dispenser struggles/jams due to a damaged bin

• Disconnect power to the refrigerator and switch the ice maker off
• Remove any ice, then pull the old bucket straight out
• Clean the area, then slide the new bucket in until fully seated
• Restore power and resume ice production

Center hinge assembly supports the refrigerator door at mid-cabinet, providing smooth pivot and proper alignment. Replace if door sags or seals poorly.

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Plastic cap that covers and protects the refrigerator door hinge assembly. Replaces cracked, broken, or missing caps to restore a finished look.

Plastic cover that snaps over the freezer door hinge to conceal hardware and protect the hinge area. Replace if cracked, broken, or missing.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

Secures and aligns the water pitcher in your refrigerator door. Replace if cracked, broken, or missing to keep your pitcher stable and organized.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This is a defrost sensor and control assembly that monitors the evaporator temperature in your refrigerator. It signals the defrost system to activate and terminate the defrost cycle at the proper times. Replace this sensor if your refrigerator is building up excessive frost on the evaporator coils, running constantly, or not maintaining proper temperatures.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection