Lg Refrigerator LDNS22220W Parts

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Center hinge assembly supports the refrigerator door at mid-cabinet, providing smooth pivot and proper alignment. Replace if door sags or seals poorly.

This is a condenser fan motor that mounts near the compressor at the back or bottom of the refrigerator. It circulates air across the condenser coils to dissipate heat and keep the compressor running efficiently. Replace this motor if the refrigerator is running warm, the compressor is overheating, or you hear unusual noises or no fan operation coming from the rear of the unit.

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This is a defrost sensor and control assembly that monitors the evaporator temperature in your refrigerator. It signals the defrost system to activate and terminate the defrost cycle at the proper times. Replace this sensor if your refrigerator is building up excessive frost on the evaporator coils, running constantly, or not maintaining proper temperatures.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Secure refrigerator panels, brackets, and internal components with this replacement mounting screw. Ideal for missing, stripped, or damaged fasteners.

Fix refrigerator vibration and rattling noise with this compressor damper. Cushions the compressor to reduce metal-on-metal contact and wear.

This is a cover assembly that sits on top of the crisper drawers in the refrigerator, forming a shelf that helps regulate humidity and temperature in the crisper compartment below. It typically includes a glass or plastic panel with a frame. Replace this cover if it is cracked, broken, or no longer sits properly, which can lead to poor humidity control and premature spoiling of fruits and vegetables.

Replace a cracked or missing produce bin so fruits and vegetables store at the proper humidity and your fridge stays organized. This direct-fit crisper drawer restores clean, reliable storage in the fresh-food section.

What it does

• Stores produce at a humidity level intended for fruits and vegetables
• Restores smooth pull-out/push-in operation when paired with intact slides
• Helps prevent spills and items dropping behind the drawers
• Replaces damaged bins that stick, wobble, or won’t seat correctly

What’s included
One vegetable/crisper drawer (sold individually).

Install notes

• Slide the old bin straight out; align and seat the new bin on the guides—no tools required
• Do not force; ensure the rail guides and center track are fully engaged
• Hand-wash only; avoid harsh cleaners that can stress and crack plastics

Usage tip
Keep heavier items on shelves above; overloading the bin can crack corners and stress the rails.

This is a rail guide assembly that allows a refrigerator drawer to slide in and out smoothly. It mounts inside the refrigerator cavity and supports the drawer's weight while enabling easy access to stored items. Replace this part if the drawer is difficult to open or close, feels wobbly, sticks, or has come off its track.