Lg Refrigerator LFC24786SB Parts

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This replacement ice bucket stores the ice produced by your refrigerator's ice maker and positions it for dispensing. Replace a cracked, warped, or missing bin to restore clean, reliable ice storage and proper dispenser performance.

• Collects and holds harvested ice until dispensed
• Seats securely to support consistent ice dispensing
• Helps prevent spills and stray ice in the compartment
• Replace if cracked, warped, has broken tabs, won't sit flush, or the dispenser struggles/jams due to a damaged bin

• Disconnect power to the refrigerator and switch the ice maker off
• Remove any ice, then pull the old bucket straight out
• Clean the area, then slide the new bucket in until fully seated
• Restore power and resume ice production

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

Refrigerator lamp light cover assembly protects the interior bulb and sensor. Replace if cracked, discolored, or broken to restore proper lighting.

Replace your refrigerator's LED light assembly when interior lighting dims or fails. Restores bright, energy-efficient illumination. Verify fit with model number.

Secure refrigerator panels, brackets, and internal components with this replacement mounting screw. Ideal for missing, stripped, or damaged fasteners.

Interior light won't turn off when door closes? This refrigerator door switch cover protects and aligns the switch for proper operation. Simple DIY fix.

Fix refrigerator vibration and rattling noise with this compressor damper. Cushions the compressor to reduce metal-on-metal contact and wear.

This replacement condenser assembly includes the attached wiring harness that secures and connects condenser-area components. It restores the factory wiring path for the condenser and associated electrical connections to help re-establish proper operation. What it does:

• Provides the condenser mounting/connection assembly and pre-attached wire harness for condenser-area components
• Restores factory routing and connector locations for reliable electrical connections
• Commonly replaced when condenser-area wiring is damaged, frayed, or disconnected
• Can resolve symptoms such as cooling loss, intermittent condenser fan operation, or electrical faults localized to the condenser area

• One condenser assembly with attached wire harness

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the rear service panel; keep fasteners and grounding in mind
• Match connectors and wire routing to the original layout; avoid pinching or sharp bends