Lg Refrigerator LFCS25663S Parts

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

Fixes intermittent cooling or component failures caused by loose or damaged wiring connections. This connector assembly restores secure electrical links.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Covers and protects the door hinge area on your refrigerator. Replace if cracked, broken, or missing to restore a finished look and shield wiring.

Upper hinge assembly supports your refrigerator door and ensures smooth opening. Replace when door sags or gaps appear. Verify fit with your model number.

This is a sheath-style defrost heater used in the refrigerator's evaporator section. It generates heat during the defrost cycle to melt frost and ice buildup on the evaporator coils, allowing proper airflow and cooling. Replace this heater if the refrigerator is not cooling properly, frost is building up excessively on the back wall or evaporator, or the defrost cycle is not functioning.

Secures and guides your refrigerator door for smooth opening and closing. Replace if door sags, rubs, or won't seal properly. Confirm fit by model number.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

Compressible foam gasket that seals refrigerator panels to prevent air and water leaks while reducing noise. Replace when worn to restore efficiency.

This is a condenser fan motor that mounts near the compressor at the back or bottom of the refrigerator. It circulates air across the condenser coils to dissipate heat and keep the compressor running efficiently. Replace this motor if the refrigerator is running warm, the compressor is overheating, or you hear unusual noises or no fan operation coming from the rear of the unit.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

This air filter assembly helps remove odors and airborne particles from the refrigerator interior to keep stored food smelling fresher. It restores the appliance's air-cleaning function so the fresh food compartment stays more pleasant. What it does:

• Circulates and filters air inside the fresh food compartment to reduce food odors and light airborne particles
• Helps control musty or stale smells that can develop in the refrigerator
• Works with the refrigerator's air circulation system to maintain interior air quality
• Common symptom: persistent or noticeable odors from the fresh food area

• Disconnect power to the refrigerator before accessing the filter housing for safety
• Locate the filter housing in the fresh food compartment
• Slide or snap the assembly into the housing until it seats securely; no special tools typically required
• Dispose of the old filter per local regulations and verify correct seating before restoring power

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit