Lg Refrigerator LFNS22520W Parts

Replacement freezer drawer tray for bottom-mount refrigerators. Organizes frozen foods inside pull-out compartment. Replace if cracked, broken, or warped.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

Fixes intermittent cooling or component failures caused by loose or damaged wiring connections. This connector assembly restores secure electrical links.

Refrigerator won't power on or loses power intermittently? This power cord assembly replaces frayed or damaged cords to restore safe, reliable operation.

Replacement door basket that snaps into the refrigerator's inner door to hold condiments, bottles, and small items. Restores storage when the original is cracked or missing.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This is a condenser fan motor that mounts near the compressor at the back or bottom of the refrigerator. It circulates air across the condenser coils to dissipate heat and keep the compressor running efficiently. Replace this motor if the refrigerator is running warm, the compressor is overheating, or you hear unusual noises or no fan operation coming from the rear of the unit.

Replacement rail holder that secures sliding rails in your refrigerator. Installs on the frame to restore alignment. Needed when cracked or broken.

Secures panels, brackets, and trim components inside your refrigerator. Replace this fastener if it's stripped, lost, or damaged to restore alignment.

This is a defrost sensor and control assembly that monitors the evaporator temperature in your refrigerator. It signals the defrost system to activate and terminate the defrost cycle at the proper times. Replace this sensor if your refrigerator is building up excessive frost on the evaporator coils, running constantly, or not maintaining proper temperatures.

Refrigerator won't power on or no electrical connection? This power cord assembly connects your refrigerator to the wall outlet. Direct plug-in part.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection