Lg Refrigerator LFX31925WB Parts

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Replaces a cracked or broken tray cover above a storage drawer in your refrigerator. Restores a flat, supportive surface and smooth drawer operation.

Right side upper hinge.

This fan grille assembly covers and protects the refrigerator's fan while channeling airflow through the vents. Replacing a cracked or missing grille helps restore proper air circulation and can reduce noise and temperature fluctuations.

• Shields the fan blades and prevents items from contacting the intake
• Directs airflow to support even cooling throughout the compartment
• Typical symptoms: broken louvers or tabs, rattling/vibration noises, obstructed airflow, frost or warm spots near the fan area
• Restores the original airflow path and appearance after damage

• Disconnect power and clear shelves/drawers to access the panel
• Remove the screws/clips securing the old grille and retain any reusable hardware
• Position the new grille and fasten securely; ensure the fan spins freely and vents are unobstructed
• Restore power and allow temperatures to stabilize

The Door Gasket is an OEM part for LG refrigerators. It serves as a thermally-insulating boundary around the freezer door helping maintain intended sub-freezing temperatures.

Causes of a bad freezer door gasket can involve hardening of the rubber from prolonged exposure to freezer climate conditions. Mineral accumulation aggravates inflexibility over time as well.

Symptoms of a bad freezer door gasket include:

• Difficulty closing the freezer door fully or securely
• Reduced energy efficiency from cold air escape
• Premature evaporation of the door seals' adhesive
• Gap formation around the door exposing food to warmer air

This OEM LG part is also compatible with some Kenmore models.

Fix water leaking inside your refrigerator with a new filter housing assembly. Secures the cartridge and seals connections. Moderately easy DIY repair.

Support roller that mounts to the refrigerator base, allowing the unit to roll for cleaning or service. Replace if worn, broken, or causing uneven positioning.

Refrigerator not cooling properly? This air duct and evaporator cover with fan circulates cold air throughout your fridge. Moderate DIY repair.

Fix dispenser drips and spills with this refrigerator dispenser funnel. Guides water flow cleanly to prevent messes. Simple 5-minute installation.

Supports and guides refrigerator drawers for smooth gliding. Replace when worn, broken, or causing binding. Confirm fit with your model number.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.