Lg Microwave LMV2085SW Parts

Replacement mounting screw for microwave panels and components. Secures brackets, vents, and assemblies. Needed when original fastener is missing or damaged.

This fan assembly replaces a worn or failed fan to restore proper airflow and cooling performance. It installs in the appliance to move air across components for efficient operation and temperature control. What it does:

• Contains the fan motor and blade to circulate air through the appliance
• Restores airflow when existing fan is noisy, slow, or not spinning
• Helps reduce overheating by directing air over coils or components
• Stops symptoms such as unusual fan noise, warm compartments, or cooling loss

• One fan assembly (motor and blade) as shown

• Disconnect power before starting any repair to avoid shock or injury
• Handle the blade and motor carefully to avoid bending or damaging the fan
• Verify mounting location and connector orientation before securing the assembly

A flat washer used with the appliance's fastening hardware to distribute load and reduce wear. Helps maintain secure connections and prevents damage to mating surfaces for reliable operation. What it does:

• Provides an even bearing surface for bolts or screws to prevent pull-through
• Reduces friction and wear between fasteners and housing parts
• Helps keep fasteners tight and resists loosening from vibration
• Commonly used where a smooth, protective spacer is needed

• Verify correct location and orientation before reassembly
• Use manufacturer-recommended fasteners and torque specifications
• Power off and unplug the appliance before accessing internal components

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Replacement mounting screw for microwave installation and assembly. Use when original screws are lost, stripped, or damaged during service or relocation.

This is a small holder that mounts inside the microwave cavity to support a cooking rack or auxiliary shelf. It keeps the rack securely in position so food can be elevated for more even heating. Replace this support if it is broken, missing, or no longer holds the cooking rack firmly in place.

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Replaces cracked, broken, or warped outer door frame on your microwave. Secures door glass and maintains proper alignment. Restores appearance.

Fix a microwave that won't heat or has no power with this high-voltage transformer. Essential component for converting household current to microwave energy.

Microwave won't heat or makes humming noise? High voltage capacitor stores energy for the magnetron. Moderate DIY repair, requires safe discharge.

Turntable not rotating in your microwave? This synchronous motor powers the turntable rotation. Moderately easy repair that restores even heating.