Lg Microwave LMVM2033BM Parts

Halogen bulb that illuminates the cavity or cooktop below your microwave. Replace when dim, flickering, or burned out. Confirm fit with model number.

Microwave won't turn on or has no power? A failed thermostat often causes complete power loss. Moderate DIY repair requires disassembly to access.

Complete hardware kit for mounting your microwave. Includes all brackets, screws, and fasteners needed for secure installation. Replaces missing or damaged parts.

Holds the light bulb and maintains electrical connection in your microwave. Replace when socket is cracked, heat-damaged, or causes flickering lights.

Turntable not rotating or making noise? This coupler shaft connects the motor to the glass tray for even heating. Takes seconds to install—no tools needed.

Fix loud rattling or scraping noises from your microwave with a new cooling fan blade. Prevents overheating by circulating air around internal components.

Fix F4 error codes or sensor cook failures with this microwave humidity sensor. Restores automatic cooking cycles. Moderate DIY difficulty.

Fix a microwave that won't start or runs with the door open. This door interlock switch ensures safe operation by detecting when the door is fully closed.

Microwave won't power on? A blown fuse assembly is often the culprit. This part protects your microwave's circuit from overcurrent and short circuits.

This thermostat is a temperature-sensitive safety switch used in LG microwaves. It monitors internal temperature and opens the circuit when overheating is detected to help protect components from heat damage.

• Monitors temperature at its mounting location inside the microwave
• Opens on overtemperature to interrupt power for safety
• Depending on model/location, a failed or open thermostat can cause no heat, the unit shutting off mid-cycle, or no power until it cools
• Helps prevent damage to the magnetron, cavity, and wiring due to overheating

• Unplug the microwave before service; the high-voltage capacitor can retain a dangerous charge
• Note wire positions, remove mounting screws, and install the new thermostat flat against the surface for proper heat sensing
• Reassemble and test; ensure vents and filters are clear to maintain proper airflow and prevent future overheating

Weak or no ventilation? This microwave fan motor restores proper airflow to prevent overheating and eliminate cooking odors. Direct repair.

This part mounts on the cooktop and supports the small "auxiliary" burner assembly. It channels gas from the orifice to the burner head so the simmer burner lights reliably and produces a steady, even flame.

• Secures and centers the auxiliary burner head/cap on the cooktop
• Directs gas flow from the orifice to the burner head for proper combustion
• Helps position the igniter adjacent to the burner head for reliable lighting
• Common symptoms include hard-to-light or non-igniting small burner, uneven/weak flame, or a burner head that won't sit level due to a damaged base

• Shut off gas supply and disconnect power; allow the surface to cool completely
• Remove grates, burner caps, and burner heads to access the base; remove mounting hardware
• Transfer existing components (such as the orifice holder and igniter) to the new base
• Reassemble, restore gas, and check all connections for leaks before use

Threaded nut assembly secures internal components in your microwave. Replace if stripped, worn, or missing to eliminate rattling and maintain alignment.

Microwave won't heat? A failing high-voltage capacitor disrupts the heating circuit. This part stores electrical energy for consistent operation.

This auxiliary burner holder mounts on your gas cooktop or range and supports the smaller auxiliary/simmer burner. It properly positions the flame ports and igniter for reliable lighting and an even, stable flame.

• Supports and locates the auxiliary burner over the gas orifice
• Aligns with the igniter for quick, consistent ignition
• Helps maintain even flame distribution and low-heat control
• Common signs of failure: burner won't light or lights intermittently; uneven/yellow flames; burner cap won't sit level or wobbles

• Turn off gas supply and disconnect power; allow the appliance to cool completely.
• Remove grate, burner cap, and burner head from the affected position.
• Note the holder's orientation; detach the old holder and clean the mounting surface.
• Align the new holder with the gas orifice and igniter, secure with the original screws, reassemble, and test burner operation.

Microwave not responding to buttons or display blank? This control board assembly regulates functions and power levels. Moderate difficulty repair.