Lg Refrigerator LTC20380SB Parts

Adjustable leveling leg assembly stabilizes your refrigerator and ensures proper door alignment. Replace worn legs to reduce vibration and noise. Confirm fit.

This replacement fan blade mounts on the fan motor to move air for proper cooling. A cracked, loose, or damaged blade can cause noise and weak airflow—replacing it restores smooth, reliable air circulation. What it does:

• Drives airflow to help maintain stable temperatures throughout the appliance
• Supports efficient cooling by circulating air across key areas
• Common symptoms include rattling or scraping near the fan, vibration, or wobbling
• Replacement is recommended if the motor runs but the blade slips, doesn't spin, or is visibly damaged

• 1 fan blade

• Disconnect power before servicing
• Access the fan area by removing covers/shelves as needed
• Note blade orientation; pull the old blade straight off the shaft and press the new blade on until fully seated
• Spin the blade by hand to confirm clearances, reassemble, and restore power

This is a defrost temperature sensor that monitors evaporator coil temperature and signals the defrost control board to initiate or end defrost cycles. It helps prevent excessive frost buildup on the evaporator, ensuring proper cooling performance. Replace this sensor if the refrigerator is not cooling properly, frost is accumulating heavily on the evaporator coils, or the unit is running continuous defrost cycles.

Center hinge assembly supports your refrigerator door at the middle pivot point for proper alignment and smooth operation. Replace if door sags or won't seal.

Attaches to your refrigerator's crisper cover humidity vent to control airflow for produce storage. Replace if cracked, broken, or missing.

Replacement water injection tube for your refrigerator. Routes water to the ice maker or dispenser. Install when original is cracked, kinked, or leaking.

Door hinge screws secure the refrigerator door hinges to the cabinet frame, allowing proper door operation and alignment. Replace when doors sag, don't close properly, or screws are loose, stripped, or missing causing door misalignment.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Limits refrigerator door travel and cushions opening angle. Replace if cracked, broken, or missing to prevent hinge damage and restore smooth movement.

Fridge not cooling or freezing? Compressor running constantly? This compressor set assembly restores cooling. Complex repair requiring professional tools.

Display not working or showing incorrect temperature? This refrigerator display control board manages temperature settings and interface functions.

Secure refrigerator components with this mounting screw. Replaces missing, stripped, or corroded fasteners. Restores tight fit and alignment.

The Door Basket is an OEM accessory specifically designed for LG refrigerator doors containing vegetable drawers. This hanging basket provides auxiliary storage directly above crisper bins.

Causes of a bad door basket can include wear and tear over time compromising the mesh material, or damage from overloading reducing structural integrity.  

Symptoms of a bad door basket include:

• Holes or tears reducing usable capacity   
• Detached fasteners slipping off mounting brackets
• Warped contours no longer remain properly installed
• Insecure attachment inhibiting safe door openings  

Replace yours today with this genuine OEM LG basket to maximize organizational convenience. Sturdy brackets produce a snug, stable fit. Compatible with Samsung, GE, and Frigidaire refrigerators featuring dual-drawer doors, this upgrade complements any modern kitchen setup. Reliable performance preserves aesthetic appeal.