Lg Refrigerator LTN19312SW Parts

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

The refrigerator door stop guide is a small bracket or track component that controls how far your refrigerator door swings open and keeps it from opening too wide. It protects the door hinges, shelves, and walls from damage caused by the door swinging freely. Replace this part if your refrigerator door swings open too far, feels uncontrolled, or if the existing guide is cracked or broken.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

This is the rubber door gasket (seal) that lines the edge of the freezer door on a refrigerator. It creates an airtight seal when the door is closed to maintain proper temperature and prevent cold air from escaping. Replace this gasket if you notice frost buildup inside the freezer, the door does not seal tightly, or if the gasket is torn, cracked, or warped.

Secures panels, brackets, and trim components inside your refrigerator. Replace this fastener if it's stripped, lost, or damaged to restore alignment.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

Replacement mounting screw secures panels, brackets, and components inside your refrigerator. Needed when original screw is missing, stripped, or worn.

Replacement mounting screw for refrigerators. Secures panels, shelves, or components inside your fridge. Order if original is stripped, missing, or lost.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

Mounting screw for refrigerator assembly. Replaces lost, stripped, or damaged screws used to secure internal components and panels. Essential hardware.

Replacement glass shelf for refrigerator interiors. Restores a cracked, broken, or missing shelf to safely organize food and use full storage capacity.

Replace your cracked, broken, or worn refrigerator door bin. This basket installs on the door interior to organize condiments and beverages.

This is a small roller used inside the refrigerator to support and allow smooth movement of drawers, shelves, or other sliding components. It helps ensure that parts glide in and out easily without friction or binding. Replace this roller if your refrigerator drawers are sticking, making grinding noises, or sitting unevenly on their tracks.

Replacement mounting bolt for refrigerator components and assemblies. Needed when original fastener is missing, stripped, or damaged during service work.

Refrigerator door stopper bumper that prevents door from overextending. Replace if cracked, broken, or missing to protect door hinges and cabinet.