Lg Microwave MA1302S Parts

The Switch, Micro is an OEM part for LG microwaves. This micro switch is crucial for the operation of the microwave door mechanism, ensuring that the microwave only operates when the door is securely closed.

Causes of a bad micro switch can include wear and tear from frequent use, damage due to electrical faults, or physical impact that disrupts its functionality.

Symptoms of a bad micro switch include:

• The microwave not starting or stopping unexpectedly
• The door not latching properly
• The microwave light not turning on or off correctly
• Error messages appearing on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.

Microwave won't heat but runs normally? A failed magnetron is the likely cause. This part generates the microwaves that cook food. Moderate DIY repair.

Microwave not heating or making loud buzzing noise? The high voltage diode regulates power to the magnetron. DIY repair typically takes 30-45 minutes.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

This holder assembly secures the locker/latch mechanism in place so the door or access panel aligns and closes properly. Replacing a cracked or missing holder restores secure engagement and smooth, reliable operation. What it does:

• Supports and positions the locker/latch mechanism
• Maintains alignment for consistent latching and closing
• Common symptoms of a failed holder: loose latch feel, misalignment, door/panel not staying closed, or visible cracks/broken mounts
• Direct-fit replacement to restore proper support

• 1 holder assembly

• Disconnect power to the appliance before servicing.
• Access the locker area and retain any screws/clips; transfer any reusable hardware from the original holder as needed.
• Align the new holder with existing mounting points and tighten screws evenly—do not overtighten.
• Test latch engagement and door/panel operation before final reassembly.

Microwave won't start or stops mid-cycle? This door latch assembly engages door hooks and activates interlock switches to restore proper operation.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

Microwave not heating or sparking inside? This high voltage capacitor stores power for the magnetron. Common repair taking 30-45 minutes with care.

This thermostat controls refrigerator temperature to help maintain proper cooling and prevent spoilage. It replaces a failed or inaccurate temperature control to restore consistent operation. What it does:

• Senses internal temperature and signals the compressor to cycle on/off
• Helps keep food at steady, safe temperatures when functioning correctly
• Commonly replaces thermostats that cause warm temperatures or inconsistent cooling
• Works as a direct replacement when matching the OEM part number

• Always disconnect power to the appliance before servicing to avoid shock or injury
• Handle the sensor and terminals carefully; avoid bending or damaging components
• Basic hand tools are typically required; follow your model's service manual for exact instructions

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

This 4.0x16mm tapping screw secures trim, panels, and brackets on ranges and microwaves. Replace missing, stripped, or damaged screws during repair.

Replacement mounting screw for microwave installation and assembly. Use when original screws are lost, stripped, or damaged during service or relocation.

Supports the turntable drum for smooth rotation. Replace if cracked, broken, or worn to eliminate scraping noise and restore stable spinning action.

Tapping screw for securing microwave panels and components. Replace if stripped, missing, or corroded during repairs or reassembly of your microwave.