Lg Microwave MV2040BSDL Parts

Microwave not heating evenly or turntable wobbling? This glass turntable plate rotates food for consistent heating. Simple 2-minute swap—no tools needed.

A flat washer used with the appliance's fastening hardware to distribute load and reduce wear. Helps maintain secure connections and prevents damage to mating surfaces for reliable operation. What it does:

• Provides an even bearing surface for bolts or screws to prevent pull-through
• Reduces friction and wear between fasteners and housing parts
• Helps keep fasteners tight and resists loosening from vibration
• Commonly used where a smooth, protective spacer is needed

• Verify correct location and orientation before reassembly
• Use manufacturer-recommended fasteners and torque specifications
• Power off and unplug the appliance before accessing internal components

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Mounting screw for microwave installation and panel assembly. Replace if stripped, missing, or damaged during maintenance. Essential hardware component.

Replacement mounting screw for microwave installation and assembly. Use when original screws are lost, stripped, or damaged during service or relocation.

Interior bottom plate panel for microwaves. Covers and protects the oven floor from spills and debris. Replace if cracked, warped, stained, or missing.

Plastic cover that encloses and protects the stirrer fan assembly. Replace if cracked, melted, warped, or missing to keep debris out of the fan area.

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Microwave overheating or shutting off? This cooling fan assembly restores proper airflow to control components. Direct-fit replacement for failed units.

Exterior handle for microwave doors. Replaces cracked, broken, or loose handles that no longer grip properly. Mounts to the door front panel.

Factory mounting screw secures panels, brackets, and internal components in microwaves. Replace missing, stripped, or corroded screws to keep assemblies tight.

Mounting bracket that secures internal microwave components. Replace if your original bracket is cracked, broken, worn, or missing to restore stability.

Self-threading screw secures microwave panels and components. Replaces stripped, missing, or damaged screws to restore secure fits and eliminate rattles.