Need Help?
Call
Pivot hanger assembly for washers. Mounts inside the cabinet to support the tub suspension system. Replace if cracked, broken, or worn to restore stability.
Complete front door assembly for your washer. Replace if door is cracked, dented, warped, or fails to seal properly. Verify fit using your model number.
This is the outer rear tub assembly that includes the bearing for a front-load or top-load washing machine. It supports the inner drum and allows it to spin smoothly during wash and spin cycles. Replace this assembly if you hear loud rumbling or grinding noises during the spin cycle, notice water leaking from the rear of the tub, or the drum wobbles excessively.
Tub cover for your washer. This plastic cover mounts to the outer tub assembly. Replace if cracked, broken, or missing to protect internal components.
I watched your video on how to replace it and ordered the part through your company. It came in two days and I replaced it without any problems. Read more
Fix excessive vibration, banging during spin, or washer walking across floor. This damper assembly controls drum movement. Moderate DIY repair.
My LG front load washing machine was vibrating severly on the spin cycle. I noticed the drum was tilted toward the back of the machine, so I replaced the rear damper. The repair was straightforward: just undo the back cover and swap out the damper. Using a deep socket to push the barbs on the pins holding the damper in place made the repair easier. Read more
Usually ships within 4 - 14 days
Secures washer drum during moving or transport. Immobilizes internal components to prevent damage. Replace if missing, lost, or needed for relocation.
I recently moved (worse move ever...) and needed shipping bolts to move my washer. I had attempted to purchase this same item on another site, but they had let me go thru the process of purchasing the item a few times only to send me an email later and say they were out of stock. So I was left under the gun to get my appliances out. I received these items really quickly and I wish I had of ordered them here in the first place then I wouldn't have been so stressed. Thank you. Read more
Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.
What it does
What’s included One shipping bolt assembly (sold individually).
Install notes
Usage tip After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.
AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more
Fix LE error code or washer won't spin issues with this stator assembly. Common repair for motor lock problems. DIY-friendly, typically installed in 30 minutes.
Wendy on the phone was very helpful. WM3997HWA/01 is an all-in-one washer/dryer from 2017 and does not have a rotor position sensor on the stator. She helped determine that Stator Assembly AJB73816004 was the fix. There is also a 00 or 01 after the model number which can be found on the serial number tag when you open the door that identifies the different series. Easy repair to take on. Hope this helps. Read more
Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.
Replaced Read more
Replace your washer's drain hose if cracked, leaking, or damaged. Connects the pump to the standpipe for proper water drainage during wash cycles.
I suspected the tub gears where ready to break so I dismantled my LG WM2032HW front load washer. I found the spyder gear corroded and broken. I also found that the stainless steel drum abraded the front tub cover so bad, it was cracked. My washer is an early model and always had standing water in the door seal after a wash. What I learned is LG stopped making the orginal front tub cover and replaced it with one that had a drain hole at the bottom front edge. I also learned that this new... Read more
Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does
#1. Watched a You Tube Video #2 Watched it again #3 Followed directions and replaced control knob #4 Did laundry It was very simple, so simple a retired pilot could do it. I recommend watching you tube videos for any undertaking you aren't sure of. Happy Repairing. Read more
Secures components in correct position inside your washer. Replace if cracked, broken, or worn to restore proper support and alignment for reliable operation.
Locking pin for shock absorber.
Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.
I ordered both the hot and cold water inlet valves because I wasn't sure which one may have been faulty. I installed them exactly the way the on line video showed, tested them and reinstalled the top of the washer. Checked several days and have found no sign of water. This was such an easy fix! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.