Thermador Dishwasher DWHD64EP Parts

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

This dishwasher door seal fits into the channel around the tub opening to create a tight, water-resistant barrier when the door closes. Replacing a worn seal helps stop leaks at the front of the unit and keeps cycles running efficiently. What it does:

• Forms a watertight perimeter seal between the tub and door
• Helps contain water and steam during wash and rinse cycles
• Aids proper door compression for reliable closing
• Common symptoms: water on the floor at the front, drips from door corners, visible cracks/flattening, or gaps in the gasket

• 1 door seal

• Disconnect power and turn off water supply before servicing
• Remove the old seal and clean the gasket channel thoroughly
• Start at the top center and press the new seal evenly into the groove without stretching
• Close the door to check for uniform compression, then run a short test cycle to inspect for leaks

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

Washer that distributes load for screws connecting dishwasher handle components. Replace if cracked, worn, or missing to ensure secure handle mounting.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Captures small food particles and debris to protect your dishwasher pump and prevent clogs. Replace when clogged or damaged. Verify fit with your model.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.

If your dishwasher detergent dispenser won't open during the wash cycle, this actuator lever assembly with springs restores mechanical movement.

Replacement adjuster socket for dishwasher leveling feet. Installs at cabinet base to raise or lower the unit for level installation. Replace if cracked or stripped.

Secures hoses to fittings, preventing leaks at connections. Replace when clamps lose tension or show corrosion. Confirm fit with your model number.

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.