Thermador Range PG364GLBS Parts

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

Fix leaks or flow issues in your range with this routing tube. Replaces worn or cracked tubes to restore proper liquid and airflow in your appliance.

Internal electrical wire for ranges. Connects electrical components within the appliance. Replace if wire is damaged, frayed, or connection is loose.

Replace your worn range door seal gasket to restore proper sealing and prevent heat loss. This flexible gasket creates a tight barrier around the door edge. Confirm fit with your model number before ordering.

Replace a cracked or missing spacer for your gas range. This small structural component helps maintain proper spacing between parts during installation.

This pressure regulator controls and stabilizes incoming water pressure to the appliance, helping maintain consistent operation and protect internal valves and seals. Fits systems that use a 3/4 inch inlet regulator. What it does:

• Reduces high incoming water pressure to a safe, steady level for the appliance
• Prevents pressure-related leaks, valve chatter, and premature wear on seals
• Helps maintain consistent water flow for reliable cycles and operation
• Commonly replaced when irregular pressure, humming valves, or water leaks occur

• One pressure regulator (3/4 in.)

• Turn off water supply and power to the appliance before starting; relieve system pressure first
• Inspect connection fittings and seals; use appropriate thread sealant if required by the OEM
• Tighten to manufacturer torque recommendations and check for leaks after restoring water

Fix erratic temperature readings or a stuck display on your range. This temperature display assembly restores clear temperature readouts and control feedback.

Secures your freestanding range to the floor to prevent tipping. Replace if bracket is missing, broken, or damaged during appliance installation.

Replace your worn or damaged 36-inch range door assembly to restore proper sealing and heat retention. Ensures tight closure and improves appearance. Verify fit with your model number before ordering.

Removable floor panel that covers the bottom of your range oven cavity. Replace if cracked, warped, or missing to protect internal components.

Protects your range's blower assembly and directs airflow for proper ventilation. Replace if cracked, damaged, or airflow is restricted. Verify fit.

Gas range fixing kit secures components and prevents rattling or loosening. Replace when parts become loose or unstable. Verify fit with your model number.

This deflector redirects dishwasher spray to the rack and helps prevent the spray arm from hitting dishes. Replace a cracked or broken deflector to restore proper water coverage and reduce spraying issues. What it does:

• Directs wash water from the spray arm for better coverage of dishes
• Keeps the spray arm clear of obstructions so it can rotate freely
• Helps prevent water from spraying into areas it shouldn't
• Common symptom: visible damage, cracked or missing deflector causing poor cleaning or spray-arm interference

• Disconnect power and water supply before servicing
• Remove the lower rack to access the spray arm and deflector
• This deflector typically snaps or screws into place; use hand tools as needed
• Inspect spray arm and mounting area for debris or damage during replacement

This slimline grill knob is the replacement control used to adjust the grill function and heat settings on compatible units, restoring precise user control and a finished appearance. What it does

• Turns smoothly to select grill heat levels and activate grill functions
• Replaces worn, cracked, or non-responsive knobs that impede control
• Matches the slim profile used on select grill/control panels for a factory look
• Helps prevent accidental setting changes by providing a secure grip

• One replacement slimline grill control knob

• Pull the old knob straight off the control shaft; press the new knob firmly onto the shaft until fully seated
• Confirm shaft type (splined or smooth) before installing to ensure proper fit
• Disconnect power to the appliance before servicing electrical or control components