Thermador Range POD301 Parts

Fix an oven that won't reach set temperature or shows inaccurate readings. This temperature sensor monitors heat levels for proper cooking performance.

The Control Board is an OEM part for Bosch wall ovens. It serves as the main control center for the oven, managing and regulating all the functions, including temperature settings, cooking modes, timers, and the operation of the heating elements. 

Causes of a bad Control Board can include electrical surges, wear and tear from prolonged use, exposure to heat, and moisture or grease buildup that can damage electronic components.

Symptoms of a bad Control Board include:

• The oven not powering on or failing to respond to control inputs
• Display errors or malfunctioning display screen
• Inaccurate temperature regulation or inability to maintain set temperatures
• The oven not completing cooking cycles or shutting off unexpectedly

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replace your worn oven door gasket to restore a tight seal, prevent heat loss, and maintain consistent baking temperatures. Confirm fit with your model number.

Fix a burned out or non-working heating element in your wall oven. This replacement element restores proper temperatures. DIY-friendly, takes about 20 minutes.

Fix an oven that won't reach temperature or gradually loses heat. This bake element generates heat for cooking. Moderate DIY install with clips.

This meat probe sensor is a temperature-sensing device that inserts into food while it cooks in the oven, allowing the oven to monitor the internal temperature and automatically stop cooking when the target temperature is reached. It connects to a jack inside the oven cavity via a heat-resistant cable. Replace this probe if your oven no longer reads the food temperature accurately, displays a probe error code, or if the cable or tip is visibly damaged.

Seals the oven door to retain heat and improve efficiency. Replace if you notice heat escaping or uneven cooking. Verify fit with your model number.

Replacement inner door glass panel for wall ovens. Installs between door layers to restore protection when original glass is cracked or shattered.

Uneven baking or slow heating in convection mode? A failed convection fan motor stops hot air circulation. Moderate DIY repair restores even cooking.

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This is a telescopic oven rack that slides out smoothly on ball-bearing glides, making it easier to access heavy dishes without reaching deep into a hot oven. It fits standard 30-inch wall ovens and replaces a fixed rack with a pull-out design. Replace this rack if the sliding mechanism is bent, the glides no longer roll smoothly, or the rack is warped from heat damage.

Factory fixing kit with mounting hardware to secure panels, brackets, or trim on your wall oven. Replaces worn, missing, or damaged fasteners for alignment.

Replacement glass panel for wall oven doors. Restores appearance when original glass is cracked, chipped, scratched, or broken. Direct fit part.

Replace your wall oven door latch if the door won't stay closed, the oven won't start, or cycles are interrupted. Restores proper door closure and locking.

This metal mounting bracket secures internal components and panels to restore proper alignment and reduce rattling. It's a straightforward replacement part that helps keep appliance panels and assemblies firmly in place for reliable operation. What it does:

• Provides a secure attachment point for panels or internal assemblies to prevent movement and vibration
• Helps correct alignment issues that can cause rubbing, gaps, or noise
• Restores the original fit where a bent, cracked, or missing bracket caused loose parts
• Works with the appliance's existing fasteners and mounting points

• Remove power and, if applicable, disconnect the appliance from water before beginning work
• Use the factory fasteners or OEM replacement screws to secure the bracket in the original location
• Verify alignment of the attached panel or assembly before fully tightening fasteners