Thermador Range PRG484ECG Parts

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Replacement drip pan for gas cooktops and ranges. Sits beneath burners to catch spills and protect the cooktop base. Replace if cracked, warped, or rusted.

Oven or burner won't adjust temperature correctly? This range potentiometer restores variable control. DIY-friendly repair, takes about 20 minutes.

This compression sleeve forms the sealing ring for a 5/16-inch tubing compression joint, restoring a watertight connection when used with a matching compression nut and fitting. Ideal for stopping leaks and restoring reliable water lines. What it does:

• Creates the compression seal on 5/16" tubing when installed with a compatible compression nut and fitting.
• Stops leaks or drips at compression-style water connections.
• Used on appliance water lines (ice makers, water inlets) and other 5/16" tubing joints.
• Replaces worn or damaged sleeves that fail to hold a tight seal.

• Shut off the water supply and relieve pressure before working on water lines.
• Inspect and cut tubing squarely; slide the sleeve onto the tube before threading the compression nut and fitting.
• Tighten the compression nut per the fitting manufacturer's instructions and check the joint for leaks.
• Replace the sleeve if damaged or deformed.

This indicator light illuminates to show when a burner or oven element is active or still hot. It is mounted on the control panel and provides a visual safety alert during and after cooking. Replace this part if the indicator fails to light up when a burner is on, stays lit continuously, or appears dim and flickering.

Oven light not working or flickering? This low-voltage transformer powers your range's interior lights. Restores proper oven lighting function.

Oven lamp assembly provides interior lighting for viewing food during cooking. Replace when bulb burns out or housing cracks. Verify fit with your model.

Replace your cracked or faded control panel insert trim to restore appearance and proper button alignment. Fits into the control area for a clean look.

Small hardware pin that secures or pivots components in gas ranges and cooktops. Replace if worn, missing, or broken to restore proper alignment.

Fix unresponsive range controls with this push-button switch. Restores button function when controls stop working. Simple replacement for worn switches.

If your gas range broiler won't ignite or stays on continuously, the broil solenoid controls gas flow to the broil burner and may need replacement.

This pressure regulator controls and stabilizes incoming water pressure to the appliance, helping maintain consistent operation and protect internal valves and seals. Fits systems that use a 3/4 inch inlet regulator. What it does:

• Reduces high incoming water pressure to a safe, steady level for the appliance
• Prevents pressure-related leaks, valve chatter, and premature wear on seals
• Helps maintain consistent water flow for reliable cycles and operation
• Commonly replaced when irregular pressure, humming valves, or water leaks occur

• One pressure regulator (3/4 in.)

• Turn off water supply and power to the appliance before starting; relieve system pressure first
• Inspect connection fittings and seals; use appropriate thread sealant if required by the OEM
• Tighten to manufacturer torque recommendations and check for leaks after restoring water

If your burner won't light or gas flow is weak, this valve controls fuel delivery to each burner. Moderate difficulty repair, typically 30-60 minutes.

90-degree elbow orifice holder for gas ranges and cooktops. Replace this gas line connector if cracked, broken, or causing improper gas flow alignment.