Thermador Range PRG486EDG Parts

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fix an oven light that won't turn on or a self-clean cycle that won't start. This door switch monitors door position for safety and lighting.

This compression sleeve forms the sealing ring for a 5/16-inch tubing compression joint, restoring a watertight connection when used with a matching compression nut and fitting. Ideal for stopping leaks and restoring reliable water lines. What it does:

• Creates the compression seal on 5/16" tubing when installed with a compatible compression nut and fitting.
• Stops leaks or drips at compression-style water connections.
• Used on appliance water lines (ice makers, water inlets) and other 5/16" tubing joints.
• Replaces worn or damaged sleeves that fail to hold a tight seal.

• Shut off the water supply and relieve pressure before working on water lines.
• Inspect and cut tubing squarely; slide the sleeve onto the tube before threading the compression nut and fitting.
• Tighten the compression nut per the fitting manufacturer's instructions and check the joint for leaks.
• Replace the sleeve if damaged or deformed.

Oven or burner won't adjust temperature correctly? This range potentiometer restores variable control. DIY-friendly repair, takes about 20 minutes.

Oven light not working or flickering? This low-voltage transformer powers your range's interior lights. Restores proper oven lighting function.

This indicator light illuminates to show when a burner or oven element is active or still hot. It is mounted on the control panel and provides a visual safety alert during and after cooking. Replace this part if the indicator fails to light up when a burner is on, stays lit continuously, or appears dim and flickering.

Oven lamp assembly provides interior lighting for viewing food during cooking. Replace when bulb burns out or housing cracks. Verify fit with your model.

Replace your cracked or faded control panel insert trim to restore appearance and proper button alignment. Fits into the control area for a clean look.

Range oven door won't lock during self-clean cycle? This door lock assembly ensures safe operation. A moderately challenging fix with basic tools.

Small hardware pin that secures or pivots components in gas ranges and cooktops. Replace if worn, missing, or broken to restore proper alignment.

Fix unresponsive range controls with this push-button switch. Restores button function when controls stop working. Simple replacement for worn switches.

Natural gas oven burner orifice that meters gas flow for proper combustion. Replace if clogged, worn, or damaged to restore reliable oven operation.

Replacement screw for gas ranges, ranges, and wall ovens. Used to secure panels, brackets, or components during installation and repairs. Order now.

If your burner won't light or gas flow is weak, this valve controls fuel delivery to each burner. Moderate difficulty repair, typically 30-60 minutes.

90-degree elbow orifice holder for gas ranges and cooktops. Replace this gas line connector if cracked, broken, or causing improper gas flow alignment.