Thermador Range PRL484ECG Parts

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

This compression sleeve forms the sealing ring for a 5/16-inch tubing compression joint, restoring a watertight connection when used with a matching compression nut and fitting. Ideal for stopping leaks and restoring reliable water lines. What it does:

• Creates the compression seal on 5/16" tubing when installed with a compatible compression nut and fitting.
• Stops leaks or drips at compression-style water connections.
• Used on appliance water lines (ice makers, water inlets) and other 5/16" tubing joints.
• Replaces worn or damaged sleeves that fail to hold a tight seal.

• Shut off the water supply and relieve pressure before working on water lines.
• Inspect and cut tubing squarely; slide the sleeve onto the tube before threading the compression nut and fitting.
• Tighten the compression nut per the fitting manufacturer's instructions and check the joint for leaks.
• Replace the sleeve if damaged or deformed.

Oven or burner won't adjust temperature correctly? This range potentiometer restores variable control. DIY-friendly repair, takes about 20 minutes.

Oven light not working or flickering? This low-voltage transformer powers your range's interior lights. Restores proper oven lighting function.

This indicator light illuminates to show when a burner or oven element is active or still hot. It is mounted on the control panel and provides a visual safety alert during and after cooking. Replace this part if the indicator fails to light up when a burner is on, stays lit continuously, or appears dim and flickering.

Oven lamp assembly provides interior lighting for viewing food during cooking. Replace when bulb burns out or housing cracks. Verify fit with your model.

Replace your cracked or faded control panel insert trim to restore appearance and proper button alignment. Fits into the control area for a clean look.

Small hardware pin that secures or pivots components in gas ranges and cooktops. Replace if worn, missing, or broken to restore proper alignment.

Fix unresponsive range controls with this push-button switch. Restores button function when controls stop working. Simple replacement for worn switches.

If your burner won't light or gas flow is weak, this valve controls fuel delivery to each burner. Moderate difficulty repair, typically 30-60 minutes.

This LP burner orifice (#59 drill) meters propane to the burner so your appliance produces a clean, properly sized flame. Use it for LP conversion or to replace a worn or clogged jet that affects burner performance.

• Regulates LP gas flow to the burner for correct flame size and combustion
• Used during LP conversion or when a jet is stripped, damaged, or obstructed
• Incorrect orifice size can cause small or lazy flames, yellow tips, or hard-to-light burners
• Replace if cleaning doesn't restore proper flame or the jet is damaged

• Shut off gas supply and power; allow the appliance to cool before service
• Remove burner parts to access the manifold; match the orifice to the correct burner position
• Start threads by hand and snug gently—do not overtighten soft brass orifices
• After reassembly, leak-test with soapy water and verify flame; final adjustments should follow the unit's service instructions.

Replace your worn range door seal gasket to restore proper sealing and prevent heat loss. This flexible gasket creates a tight barrier around the door edge. Confirm fit with your model number before ordering.

Replace a cracked or missing spacer for your gas range. This small structural component helps maintain proper spacing between parts during installation.

If your gas range broiler won't ignite or stays on continuously, the broil solenoid controls gas flow to the broil burner and may need replacement.

Replaces the lower kickplate on your range to restore a finished look and protect internal components. Install when your original panel is cracked or damaged.