Parts for Ge SBSD137H0MS: 01 - Pedestal Parts

A small rubber protective cap that covers exposed studs, fasteners, or component ends to prevent abrasion and reduce vibration. Fits into tight openings to protect parts and help keep connections sealed from debris. What it does:

• Covers and cushions exposed metal studs, screws or posts to prevent wear and scratching
• Reduces rattles or vibration by adding a soft buffer between parts
• Helps keep out dust and debris from small openings around fasteners
• Common fix when a visible post or mounting peg is uncovered or causing noise

• Push-fit installation — seat firmly over the post or stud until fully covered
• Power off and unplug appliance before accessing internal areas
• Inspect surrounding components and replace any damaged fasteners or mounting hardware
• If cap feels loose, check for correct fit or replace with the correct size part

This is a replacement ST4-16 sheet-metal mounting screw used to secure panels and small components on compatible appliances. It restores proper fit and prevents loose or rattling parts for a secure repair. What it does:

• Fastens trim, access panels, brackets and small components to appliance chassis
• Replaces missing, stripped or damaged screws that cause loose panels or vibration
• Provides correct thread and length for original mounting locations (ST4-16 size)
• Helps maintain safe, gap-free panel alignment for normal operation

• Use the same screw size and thread type as the original; do not over-torque
• If thread engagement is poor, inspect mating hole for damage before reuse
• Wear safety glasses and disconnect power to the appliance before working on panels
• If multiple screws are missing or hardware is corroded, replace all like-for-like fasteners

This is a replacement ST4-10 appliance screw used to fasten interior and exterior components. It provides a secure, corrosion-resistant hold to keep panels, brackets, and assemblies in place during normal appliance operation. What it does:

• Secures trim, panels, brackets, and small assemblies that use ST4-10 sheet-metal style screws
• Restores loose or missing fasteners that can cause rattling, misalignment, or part movement
• Small, high-thread engagement helps maintain a tight fit in threaded or self-tapping holes

• One ST4-10 screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Handle small parts carefully and keep track of fasteners during disassembly

This M3 x 10mm machine screw fastens small appliance panels and components, providing a secure, low-profile connection for internal brackets, trim pieces, and assemblies. Compact size for precision mounting in tight areas. What it does:

• Secures control panels, brackets, trim, and small internal parts
• Prevents rattling or loose components when properly installed
• Replaces worn or stripped fasteners that cause misalignment
• Used where a small M3 machine screw is required for reliable fastening

• Unplug appliance or switch off breaker before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten snugly but do not overtighten to prevent thread or part damage
• Keep loose screws away from heating elements and moving parts during reassembly

A standard M3 hex nut used to secure compatible M3 bolts and studs in appliance assemblies. Small but essential, it restores proper fastening where a worn, stripped, or missing nut causes loose panels or components. What it does:

• Secures M3 threaded fasteners to hold panels, brackets, or small components in place
• Replaces missing, stripped, or corroded nuts that allow vibration or movement
• Helps stop rattling, misalignment, or intermittent electrical/contact issues caused by loose parts
• Used wherever an M3 nut is specified by the appliance manufacturer

• Disconnect power and follow appliance safety instructions before accessing internal parts
• Use the correct M3 bolt and matching thread engagement; avoid cross-threading
• Tighten snugly but do not overtighten to prevent stripping threads or damaging parts
• Replace any accompanying damaged fasteners or hardware for a reliable repair

This is a replacement ST5.5 x 22 screw used to secure panels, trim, and small components on compatible appliances. It restores proper fastening to reduce vibration and keep parts aligned for safe operation. What it does

• Fastens panels, trim pieces, and small internal components
• Prevents rattling or parts coming loose during operation
• Helps maintain proper alignment of covers and assemblies
• Replaces missing or stripped screws to restore secure mounting

• Disconnect power or unplug the appliance before working on it
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack panels
• Replace only with the same size and type for proper fit and safety