Power Pro Parts

This replacement part is a hex screw. It is a genuine replacement part made by MTD. This type of part is very common in different types of appliances and machines. Hex screws are important in holding parts together so that the user is able to operate the appliance smoothly.A new hex screw might be needed if the user notices that different parts of the appliances are loose or missing. It is possible for hex screws to become stripped over time and will need to be replaced. The repair for this screw should be simple and will most likely require a screwdriver and perhaps pliers if the previous screw is stuck in place. This is a genuine OEM replacement part. This part is sold individually. It is sourced directly from the manufacturer to ensure proper fit and long-lasting use.

This tap hex screw is a genuine MTD part, sold individually. A tap hex screw can be used as a replacement part for outdoor appliances including lawn mowers, tillers, and edgers. This is a small fastener.The tap hex screw for one of these outdoor appliances might be subject to damage or to a loss or misplacement that can necessitate the full replacement of the screw. Refer to the manual for detailed instructions.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This tap hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Montgomery Wards, Bolens, Yard Man, Turf King, and MasterCut.

This part is a replacement carriage bolt. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. The intended use for this part is to properly replace a defective, lost, or stripped carriage bolt outdoor power equipment.Bolts are standard pieces of hardware that can be used in many different areas and with many different types of equipment. Bolts can become stripped, corroded, loose, or lost and will require replacement. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this particular carriage bolt, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality metal. This carriage bolt can be used with a variety of leaf blower models manufactured by MTD, Craftsman, and other brands.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.

This is a replacement spacer for walk-behind lawn mowers, riding lawn tractors, snowblowers, and other outdoor machinery. The spacer prevents parts from grinding together and wearing down. This spacer fits over the axle areas and is a small, flat, metal ring.Over time and through wear and tear, a spacer can go bad or get bent. This is also dependent on frequency of use. For equipment used maybe once a week (or month, depending on the season), replacing a spacer may never be a concern. For machines used more frequently, it may be a rather minor fix. Replacing the spacer is simple, and requires a screwdriver, pliers, wrench, and a pair of durable gloves. The replacement requires some disassembly of the lawn mower and its inner workings.This is a genuine OEM replacement spacer. This part is compatible with over 150 products and machines. This part is sold separately.

This genuine OEM replacement bracket stop seat is for riding lawn mowers or tractors. The part is located underneath the seat on riding mowers or tractors. Its purpose is to provide a safety shut off function when the rider leaves the seat while the blade is engaged. Over time, constant use of the mower can cause wear on the bracket, requiring it to be replaced. If a mower is left in the elements over an extended period of time, the bracket could rust. This would require the bracket to need replacing. Failure to replace a worn or rusted bracket stop seat could cause potential safety hazards as the engine may to fail to shut off if the rider should leave the seat while the blade is engaged. Replacing a bracket stop seat requires a screwdriver to replace. It is a fairly easy repair that should take under 30 minutes to complete. This part serves as a replacement if needed for the original bracket stop seat. This bracket is compatible with Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Husky, Montgomery Wards, Bolens, Yard-Man, and Ryobi brands. This bracket is sourced directly from the manufacturer and is sold individually.