Andrew Fox September 30, 2021 for Model Number Thermidor PRG364GDH/03 Oven shuts down when heating above 400. Oven light starts flashing. Is the problem with the control board?
1 Answer Andrew, It would be recommended to check the oven sensor for the proper resistance of 1090 at room temperature. If the sensor is off then it will need replaced and if this checks ok then the oven potentiometer will be the most likely cause for this issue. Read More...
Sean April 03, 2021 for Model Number PCG364ED/03 Two left side ignition doesn't work, no click sounds, no gas. Already tried to replace the ignition switch, doesn't help. I think the main board is bad. P/N 543 90 001. Do you have the main control board for Thermador PCG364ED/03?
Iwona January 27, 2018 for Model Number prg366eh/06 Our oven does not light up. There is a gas flow but it's being turn off few seconds after it starts coming. We already replaced igniter, flame sensor and dual valve. Broiler work the same way as well, it starts and turn off. Burners work good. What can be the reason why oven does not want to keep working? Thank you
1 Answer Iwona, This issue will most likely be caused by a faulty control board. The part number for the control board is 00676192. Read More...
Daniel A. June 21, 2017 for Model Number PRG366JG/06 My oven won't reach temperature. I have it set to 400° and it only gets to 300°. I replaced main and thermostat. What else could be wrong?
Kevin M December 11, 2016 for Model Number Thermador PRG30-4EH/06 I received the potentiometers 00629722 you verified should be good for our Thermador. Disassembled the stove sufficiently to replace them. However, the original potentiometers have edge connectors. The potentiometers 00629722 received have a male Molex-style connector. So I could not connect to them. Both have five wires. What do you suggest? Thanks for your ongoing help. I have photos showing the different connectors on the potentiometer assemblies if that would be useful.
1 Answer Kevin, According to the manufacturer the correct potentiometers for your unit would be part number 00422748. Read More...
Sidney December 10, 2016 for Model Number PRG486EDPG01 Large Oven not igniting...you can hear and smell gas turn on but there is no ignition and then gas shuts off after 5-10 seconds. Replaced igniter, replace main control board, replaced smaller igniter board, tested conductivity of ignition wire from control board to igniter and it is fine. Tested temperature sensor in oven and it is within specs....dont know why large oven will not ignite...smaller oven works fine...all burners work fine...what else is left for me to check??? thx
1 Answer Sidney, You will want to pull the burner and check to make sure that there is no rust around the ports and make sure that there is nothing clogged in the orifice or that there are no cobwebs inside the burner. Read More...
Kevin Murdoch October 29, 2016 for Model Number Thermador PRG30-4EH/06 Replaced simmer board. Now blue indicator light works when a left-hand burner is switched on. But still no spark and no gas on two left-hand burners having XLO simmer. Solenoid continuity is good for both. I suspect now the potentiometers. What is the replacement potentiometer part number for my model? The circuit board on the potentiometer reads "ARK-LES Corporation 521 91F 002".
Paulo C October 24, 2016 for Model Number Control Board 00619016 Hi. I'd like to know how to know the number/name of the electrical components. Im tryin to fix the controlboard by myself, but i do not know to this. http://prntscr.com/cyebgi its the one below the blue thing
Kevin October 08, 2016 for Model Number Thermador PRG30-4EH/06 No spark and no gas on two left-hand burners with simmer control. Suspect failed simmer control board. The installed board is "ARK-LES Corporation P/N 543 90 001". Wanted to verify that fixing kit 00619016 is the correct replacement. It looks the same, aside from minor differences in component placement.
Paul September 18, 2015 for Model Number prg304gh/04 The old part had a green ground wire coming out of it. The port on the replacement part is already soldered. Do i connect the ground wire to it or not. thank you.