Lawrence August 06, 2019 for Model Number Bosch HBL5450UC/06 I have the same issue as another has reported here, but want to be sure I'm ordering the correct board. The oven is in setup mode, asking for date/time/etc. to be set. You can start to move through the entry screens, but when pressing "INFO" to complete the programming, the screen goes blank except for a square cursor in the upper-left, and then it goes right back to the setup screen again. Recycling power does not help, disconnecting from power for an hour does not help. Have tried every key combination. Is this the display board or the control board, so I order the correct one. Thanks for ANY help!
1 Answer Lawrence, the module 12022212 is going to be the main control board. The display board for your model is going to be 00703859. Read More...
John Connolly May 25, 2019 for Model Number hbl8750uc/12 My screen seems to be frozen in the main menu. When I press quite ,the screen goes blank except for 4 small bars. I feel I need to replace the control module.any information for this problem.
1 Answer John, If you are unable to program the unit then the control panel would be the issue but if it is programming but will not start then would be the main control board. Read More...
Matt January 27, 2018 for Model Number hbl5450uc/01 Just took delivery from appliance parts pros of what was designated as replacement control module (circuit board) for this model - Bosch 00655359 Module-Control But the configuration of board is completely different than what is installed in my oven. It has edge connectors and block pin receptacles that don't match existing wiring. had expected a simple unplug and plug of existing leads into replacement board. Can I find a replacement module with a matching configuration to what came with the oven?
1 Answer Matt, This control module would be the one that the manufacturer has as a replacement and would be the correct one for your unit. Read More...
Bob August 03, 2016 for Model Number HBL5450UC/06 Temp control is off. For example, when set to True Convection (325 d) it heats up quickly to 300 then slows way down and or stops. At 300 The oven reads preheat then switches to heating as it struggles to reach the set 325. I then turn up the temp to 340, the oven displays preheat again and starts to heat up again. Lastly, I turn the oven off, set the oven to True Convection (325) , re-start, the oven heats to 340 before I shut it off. Took off sensor and all elements and all checked out. Ordered a new inter-phase board "module control (from you) and did not fix the problem. Repair tech is pulling at straws. Suggestions? Is there another board to replace? Thanks,
1 Answer Bob, The control module/relay board would be the part that would cause this type of issue other than the wiring or oven sensor. If you test the oven sensor wires at the control board test for 1090 ohms at room temp of 77 degrees. The calculation for when you turn the oven on and test the sensor and wires would be to add 2 ohms for every 1 degree of increase. So it would be recommended to test at the set temperature once it goes to the heating phase. It is possible that the wiring of the sensor could be the issue. Read More...
Steve A December 06, 2015 for Model Number hbl5450uc/06 The model number HBL5450UC/06 cross reference shows control module Ap5631391 in other parts identifiers. AppliancePartsPros does not show it as a valid part number. Is this a misprint?
1 Answer Steve, The control module part number is Appliancepartspros.com part number of AP5631391 and Manufacturer part number 00659614. Read More...
Larry R. July 17, 2014 for Model Number hbl5760UC/08 I have a Bosch oven a few years old that is getting too hot and giving an E115 regulation error code. I have replaced the temperature sensor but still having the same problem. Could the problem be the control board?
1 Answer Hello Larry, Yes it certainly can be the control board 12022212 since it is a part of this circuit. Read More...
Skip January 09, 2014 for Model Number HBL5450UC/6 Is this the oem part im checking on how long does it take to ship?
1 Answer Hello Skip. Yes, it is OEM and usually if the item is in stock, it ships the day you order it if you order before 4:00 PM Eastern time. Read More...