Francesca August 22, 2020 for Model Number SHX68T55UC Our dishwasher has stopped working. It powers on and off. The control panel is always showing the express light on. As we cycle through things, that light stays on. Any ideas why? As soon as we push start and shut door, everything powers off. We have been told we need a new control panel. I'm ok with buying it if I know it will help! Also, the pump on the side of the dishwasher is now exposed since we are trying to fix it. The plastic housing which is see through is full of crud and stinks to high heaven. Any idea how to clean out/flush out the crud?
1 Answer Francesca, Yes this operating module 12010233 would be the correct part for your unit. As for the crud, once the unit is repaired use some affresh dishwasher cleaner or vinegar to clean the machine. Read More...
Vic November 22, 2019 for Model Number Bosch SXH68TL5UC/07 Our Bosch dishwasher power cord melted and shorted out inside the junction box. All the connectors were tight and wire well connected. I don't know why it happened. The dishwasher was dead and had no power. I checked and the Bosch website and the dishwasher is not covered under the Bosch recall. The dishwasher is about 3 years old. We called in two technicians. The first one replaced the junction box and power cord. The dishwasher didn't turn on. He replaced the operation program module (12010233). The dishwasher came on, but all the functions and lights were messed up, behaving erratically. After trying for a couple of hours, he said he couldn't fix it. We then called in a certified Bosch technician. The technician said that we needed to replace the Control Module, the main wiring harness (because the previous technician ruined it). I have now replaced the Control Module, wiring harness, new power cord, new junction box, new operation program module. Almost all of the electronic parts in the dishwasher are new. But still, there is no power! I checked with a multimeter, the junction and power cord are working fine. The control module is sending out a signal. The only thing I can think of is the operation program module the first technician installed is faulty or shorted out when the first technician was trying to get the dishwasher working. I have replaced every component I can think of. If the operation program module will do it, I am willing to try as this or any other fix I can do myself. I hate to throw an almost brand new dishwasher away but also don't want to throw good money after bad. PLEASE HELP (very frustrated)! Thank you. Vic
1 Answer Vic, With power coming out of the control module and the module not coming then this would be an issue with the Operating module. It would be suggested to check the door switch first but the module would be more likely. Read More...
Bob September 05, 2019 for Model Number SHX68T55UC/02 Have been getting water tap error for a while. Now am getting E15 error and water in the float sensor underneath. I have replaced the water inlet valve thinking that was the problem. The problem is that water inlet valve comes on when the dishwasher calls for water but it doesn’t shut off causing the water to overflow. This was happening with the original valve and now with the new one. Do I need to replace the operating module program or the control module programme?
Bb August 17, 2019 for Model Number SHXN8U55UC/06 I have two problems. 1) The control panel is not fully working so it's hard to read the numbers/time 2) I get the water-tap error all the time. I check the filters and the drain and there doesn't seem to be any blockage
1 Answer BB, Based on the information it does sound likely that the operating module would need to be replaced. For the water tap issue, this would have to do with incoming water supply so you would want to make sure that the water valve is getting power and inputting the correct amount of water. If it is not getting power the mainboard would be the issue and if it is getting power but not enough water or no water then the valve would be the issue. Read More...
Matt August 16, 2019 for Model Number SHX68T55UC/02 Have error code E01. Getting different answers as to the problem. One says pump/heater one says relay on control module and another says power module. Would appreciate your estimate. Thanks
1 Answer Matt,I am finding all references referring to the E01 code states an issue with the motor. specifically that you need to replace the power control module. Before doing this first check the sump area around and under the filter to make sure something has not gotten down in there and blocked the motor from turning, if all is clear then they recommend5780405 replacement of the power control module part number 00752739 Read More...
Orlando December 04, 2017 for Model Number SHX68T55UC/02 I also had lightning strike ,my operating module AP5986106,not working only flashes red add salt,add rinse aid that is all Nothing else works.
1 Answer Orlando, For this issue you will need to replace the operating module part 00752739 is most likely faulty due to the lightening strike. Read More...
Gary B October 15, 2017 for Model Number SHX68T55UC/02 We had lightening hit a power pole outside our home and lost our phones, and also the dishwasher hasn't worked since. I have power 118 volts at the box behind the washer but the controls on the door are dead. They will not reset. Would replacing the control panel be the answer or is there other things to look at first??
1 Answer Gary, The control module 00752739 would be the most likely cause for the unit to not want to operate. Read More...