Jay November 02, 2015 for Model Number 790419310 I replaced oven clock when it blew, and as soon as I plugged it up it blew again. Is it the element in oven that is bad or what???
1 Answer Hello Jay. You will need to check the element and all wiring on the unit. You have a dead short somewhere in the unit. Read More...
Barbara September 16, 2015 I have to replace a slide-in gas range. Can I use a free-standing range to replace it or do I have to buy a slide-in
1 Answer Hello Barbara. If there is room in the cabinets for a free standing, then you can use one. You will need to measure the opening to see. Read More...
Joan August 15, 2015 for Model Number glefs77cbc A loud pop as using oven. Range works. Control board has an L and bake time light on. Do I need a control board.
1 Answer Joan, Based on what happened and what is showing on the display with no oven operation, the control board 316207529 on the unit would need to be replaced. Read More...
1 Answer Hello Tina. You need to check at the terminal block for 240 VAC coming to the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Carol May 29, 2015 for Model Number Frigidaire gas stove 15 years old The clock quite working a few days ago. What could the problem be? Thanks. Carol
Louise F. April 17, 2015 for Model Number FES355CCSH The readout for the time is a bit dim, but the readout for temperature and function is barely visible in a darkened room and impossible to read in daylight. It there a solution without replacing the whole control unit? Louise F
1 Answer Hello Louise, The only way to correct this is by replacing the clock assembly 318012943. I'm sorry but this part has been discontinued by the manufacturer and no satisfactory substitutions have been provided. The only choice at this point is to have the board replaced or repaired. Read More...
Karen January 16, 2015 for Model Number GLEFS77CSD Went to bake rolls oven came on perfectly. Timer went off the oven warm only, now it will not heat. No code. What can be the problem? Is it the oven element
1 Answer Hello Karen. Test the elements they should read closed for continuity. If they are good, you will need to order and replace the control board in the unit. Read More...
Chares November 30, 2014 for Model Number GLEFS77CQC When replacing the main control unit should you order a new cover also?
1 Answer Chares, I would recommend also purchasing the overlay 316220804 as they are a peel and stick type and can tear when removing. Thanks. Read More...
Ronnie125 October 28, 2014 for Model Number FGGF3041KFK I was using the broiler today and noticed that the overlay on the electronic clock control board looked melted. When I flet the overlay, it was really hot and almost burned my finger. The control board seem to work fine.Not sure exactly what the problem is. Any feedback will he very helpful. Thanks, Ronnie125
1 Answer Hello Ronnie125. The heat from the oven vents out under the control panel. When broiling, you should leave the door open so it does not get hot enough to melt the overlay. Read More...
Aprilmay September 29, 2014 for Model Number FEFL78CBA Hi, I was cooking in the Oven part of the stove, Ten minutes into the cooking we heard a loud POP and all power was gone, it Also tripped the Breaker. Unplugged it for a day, And just turned everything back on the clock said 100. Then started Reading F1 and Beeping loudly. Unplugged again! Please Help I need my Stove :( Thank you
1 Answer AprilMay, The F1 error code means that there is a runaway temperature. You will want to check the oven sensor for resistance which should be 1090 ohms at room temp. If the sensor checks ok then replaced the oven control board. Read More...