1 Answer Hello Jerry. Test for power to the element from the control board. If none is there, you will need to replace the control board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jerry November 22, 2013 for Model Number FEFL78CSA The preheat light comes on but the oven will not heat.
1 Answer Hello Jerry, Flip the breaker off and back on first. If trying the unit again and it heats, the issue was a loss of the second leg of 120Vac. If the surface units work the voltage will not be the issue but the problem will most likely be either a bad bake element 316202200 or a bad control 316207529. Read More...
Alicia November 07, 2013 for Model Number GLEF378CSE Screen is out broil light stays lit but broiler is not on, no way to control the oven. Would replacing the control board resolve this issue? -stove top works fine-
1 Answer Alicia, Yes, Based on the post description, the issue is in the Clock / ERC 316207529, you may also want to consider the "overlay" 316220804 they have a tendency to wrinkle and bend when transferred from the original clock to the replacement clock, unless you're very careful. Read More...
Jim September 06, 2013 for Model Number FEFL77ASH Hi, Problem is similar to others. Loud pop, breaker out, etc. Surface elements o.k. oven not working. Followed testing procedure in manual, pg. 44 for “No Heat.” Bake to neutral, clock operating only was 0 volts. Programmed oven control for bake. Line to line on both BK and BRL elements was 0 volts, not 240. Disconnected wires. Wires tested 1.4 ohms. My meter not accurate, probes crossed shows 1.8 ohms. Does that mean wires are 0.4? BK element was 17.2 ohms. BRL element was 15.2 ohms. Reconnected wires to BK and BRL on EOC but not to elements. Oven programmed for bake. Bake side at element (blue) is 120 volts. L2 out is 0 volts at element, but reads120 volts at EOC. Is Control clock good or bad? Help. Please explain. Jim
John C. July 10, 2013 for Model Number GLEF378CBB (Frigidaire Gallery Series range/oven) I'm pretty handy around the house -- I have tools and have done many things in the past -- but have never attempted to repair an oven. How hard is it to replace an oven control board?
John Mac June 07, 2013 for Model Number glewfs77csb I told you in my last e-mail that my oven buttons come on but neither elements work and that my clock works. You told me that if i am getting 240 volts across bake and L1 that my control board was bad. Did you possibly get that backwards? I don't get anything and I have checked both elements and anything else that I know to check and think the only thing left is the control panel?
1 Answer John, If you are not getting 240 vac from bake to L1 with bake turned on, then you will want to then check from Bake to neutral. If there is power there then the control is bad and would need to be replaced. If there is no power then you will want to check the circuit back from the control board through the element, if there is a high limit, and to the L2 on the terminal block. You can test this side with the control board in the off position as there should be 120 vac coming to this side of the circuit. Read More...
John M June 03, 2013 for Model Number glefs77csb When I press the oven or broiler button it comes on for a few seconds and then goes off and neither element heats up; the clock works!
1 Answer John, You will want to check to see if the control board is getting 240 vac between bake and L1 when the unit is turned onto bake. If it is then the control board 316207529 is bad and would need to be replaced. Read More...
Tom March 12, 2013 for Model Number FEF366CCB i am getting F1 on the display and my oven keeps locking/ I turned the breaker off and removed the clock module. When I took the 1st board out there was black scoring on it and there was black scoring on the clock board. Is it ok just to replace the whole assembly which is part number 316207511 or is there a more serious problem? I disabled the beeper and have been using the stove , I just have no use of the oven. I just wanted to make sure it was ok to just replace the part # listed above or am i just going to blow the replacement board? thank you Tom
1 Answer Tom, The F1 error code is for a runaway temperature. You will want to replace the clock but also check the oven sensor resistance. Should be around 1090 ohms at room temp. There will be a differential of 10 percent up or down. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Johnny-O February 19, 2013 I have a frigidaire oven and the control board/ clock went out, the model number is 316207509. Is there any other control board that I can use in place of this one?
William January 08, 2013 for Model Number Fregidaire range FEFL78CQC The oven popped while running,both bake and broil and clock stopped working the stove top still works.I checked the elements with ohm test and both elements are ok. Do You think I need and new oven conrol board?part no AP3764682
1 Answer Hello William, It does sound like the control board blew out. You can test to make sure that you are getting power to the board by checking for 120vac from L1 to Neutral on the board. If you have power then you need new board. If no power you will want to trace wiring back to terminal block. Read More...