Mike August 28, 2023 for Model Number FASE7073LA0 Tried 2 new user interface modules for an issue with the dry mode rotary knob, both new interfaces give me an E93 error code. Put in original interface and no code/dryer works. Interface module #137260610, main module #137249940. The date code on the harness between the 2 modules is 5-27-2010. Tried code clear and resets still no change with new modules. Any ideas? Thanks
1 Answer Hello Mike, check the part number on the original U/I board and see if is different from the one (137260610) listed for your model, as the error code E93 refers to the boards not able to communicate with each other. Read More...
Keith March 25, 2023 for Model Number FASE7073LA0 My Frigidaire affinity dryer needed a heater thermal replacement. wires crossed and got a shock charge. Now the system does not turn on at all checked switches and thermostats the seem to be working. I have to get this back going., Please advise , Does the control box? have fuses that can be replaced? I do not see any obvious damage in the box, everythig including door switch are all working. what's the next thing to get it working
1 Answer Keith, Start by checking the machine for error codes:READING ERROR CODES:1. Wake the dryer up by pressing any button but “cancel”.2. Press and hold the “cancel” and“start pause” buttons simultaneously for 6 seconds to show the last error code recorded. The error code will appear in the display as an E followed by two numbers. NOTE: E00-means no failure code experienced.The tech sheet supplied with your machine should list the error codes and the likely solutions.You could also place the machine into diagnostic mode: DIAGNOSTIC MODE1. Press the “cancel” button to enter standby mode and enable diagnostic entry.2. Within 10 seconds after pressing “cancel”, press any button (but “cancel”) to wake up the control.3.Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the “cancel” and the center button under the display simultaneously for 3 seconds to enter the Diagnostic Mode. (note: to save time at wake-up, the welcome screen can be bypassed by turning the selector knob).4. Upon entering Diagnostic Mode, all lights should flash on and off.This information is also listed in the tech sheet packaged with your machine. Read More...
Jerry January 28, 2020 for Model Number FASE7073NA2 My dryer is displaying an E91 error. I know that means "lost contact with control board" or something to that effect. I have pulled both the control board and the control assembly and cleaned the contacts with emery cloth and contact cleaner. This worked for a couple of weeks. Now the E91 is back. Both control parts are expensive. How do I determine which to replace first? Or whether it is the wire connectors? I wish I could just buy both and return the one I don't need. What is a good guess about the sequence? Advice?
1 Answer Jerry, unfortunately, the manufacturer does not have testing procedures for this error. However, the wire harness will need to be checked for a verified full connection to the metal contacts on each control. A water-based marker can be used (unit unplugged and contacts thoroughly cleaned afterward) to find if the contacts are scraping together. If there is a contact issue, a mark will be undisturbed. Read More...
Jeremy April 29, 2019 for Model Number FASE7074LA0 OMG- I live in rural area. Having the worst time with the latest code the dryer sprung. Says "door open." Switch is definitely working. It had a code E66. So I went to replace that dryer thermal switch. Problem is, everything works including the entire heater element all has continuity. Put it all back together replacing those parts only to find out that is still says door open but now has a new code saying E-91. So I replaced the control board unit #PS3408291 and still says same. Door open and still has a code e-91. Last part I know of is #809160802 "Electronic control board." At this point, im now tripple checking myself thinking the online threads are sending me all over. lol. I just found a new thread saying that the e-91 is a Communication error between UI board and control board. Check wiring. Im at a loss right now. Im at a bit of a loss and mayby one of you guys can help me out?
1 Answer Jeremy, For the E91 error you would want to check to make sure that the wiring between the main board and the user interface are good and tight. If no wiring problems replace the main control board 809160802. For the E66 error the issue will most likely be caused by a outlet thermal limiter on the blower housing that is faulty. The control board may take care of the issue with the main control. Read More...
Rodney November 19, 2017 for Model Number Fase7073lwo Dryer has door open warning and won't start,I changed door switch and control panel.tested switch and wire to door ,what else could it be?
1 Answer Rodney, If the wiring is good and new door switch then this will be an issue with the control board of the unit. Read More...
Daniel R September 19, 2016 for Model Number FASE7073LA0 Every time you push start it will say door is open so I check the door switch and it checked good so I trace the wire back to the control board could this be my problem.
1 Answer Hello Daniel. Make sure the door strike is good. If so, and the lock and harness is good, you will need to replace the control board. Read More...
Levi October 23, 2013 for Model Number fase7073lwo The code e61 keeps coming up. Already checked volts everthing there good. Replaced control board and replaced control assembly. I hired a tech to come out and he said it had to be control assembly. Dryer still brings up code e61.
1 Answer Hello Levi. If both the board and the console are new, it sounds like the wiring harness may be bad and need to be replaced on the unit. Read More...